If you see the engine light on or the service engine soon warning light, it could be due to the P1E92 fault code. This code indicates a problem with the HybridEV Battery Interface Control Module, which could be faulty or have a poor electrical connection.
It could also be due to an open or shorted harness. The importance of fixing this issue lies in the fact that it could affect the performance of your vehicle. The difficulty level of repairing this code is moderate, and it could take around 1.0 hour to fix.
To interpret the fault code, you need to check the possible causes listed above and visually inspect the related wiring harness and connectors.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1E92: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON, it could be a sign of p1e92 fault code.
Here are the symptoms to look out for:
- The P1E92 fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience rough idling or stalling, and there may be a noticeable decrease in acceleration.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P1E92: Unveiling The Causes
The P1E92 fault code can be caused by a faulty control module, open or shorted harness, or poor electrical connection.
- The automobile fault code P1E92 can be caused by a faulty Hybrid/EV Battery Interface Control Module.
- It can also be caused by an open or shorted Hybrid/EV Battery Interface Control Module harness.
- Additionally, a poor electrical connection in the Hybrid/EV Battery Interface Control Module circuit can also trigger this fault code.
Fix Code P1E92: Simple Steps To Get Your Car Running
Below are some possible fixes for the automobile fault code p1e92, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code P1E92, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P1E92: Affordable Fix For Complex Automobiles
The automobile fault code P1E92 has an estimated repair time of 1.0 hour. The cost of fixing this fault code varies depending on the auto repair shop, but it is common for most shops to charge between $75 and $150 per hour.
These factors, along with the severity of the issue and the required parts, can influence the overall cost of fixing the fault code.
It is important to get an accurate diagnosis and estimate from a trusted mechanic before proceeding with any repairs.
P1E92: Your Car’s Battery Needs Attention
The P1E92 code is related to the HybridEV Battery Interface Control Module 1 Cell Balancing Circuit. The hybridEV powertrain control module 2 uses cell balancing to maintain a similar state of charge on the cell groups. A resistor wired in parallel with the cell group and a transistor switch in series with the resistor internal to the hybridEV battery interface control module are used for cell balancing.
The hybridEV powertrain control module 2 sends a command to the hybridEV battery energy control module to begin cell balancing through the hybridEV battery interface control modules.
FAQ
If you’re experiencing the P1E92 fault code, your engine light may be on. This could be due to a faulty Hybrid/EV Battery Interface Control Module, an open or shorted harness, or poor electrical connection in the circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P1E92 fault code, your engine light may be on. This could be due to a faulty Hybrid/EV Battery Interface Control Module, an open or shorted harness, or poor electrical connection. To fix this issue, visually inspect the wiring harness and connectors, checking for any damaged components or broken, bent, pushed out, or corroded connector pins.
If you’re experiencing the P1E92 automobile fault code, you may notice that your engine light is on. This could be caused by a faulty Hybrid/EV Battery Interface Control Module, an open or shorted harness, or a poor electrical connection in the circuit. To troubleshoot this issue, visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on, it may be due to a faulty HybridEV Battery Interface Control Module or related wiring issues.
Visually inspect the wiring harness and connectors for damage or corrosion. Check for broken or bent pins.
