The P1E63 automobile fault code indicates a problem with the HybridElectric Vehicle Battery Pack or the Battery Interface Control Module. The most common symptom is the Engine Light turning on. The cause of this issue is usually a faulty battery pack or control module.
It is important to address this issue promptly as it can lead to reduced fuel efficiency and even engine damage.
The repair process involves visually inspecting the wiring harness and connectors for any damage or corrosion. The repair time for this issue is estimated to be around 1.0 hour.
To interpret the fault code, it is recommended to check the “Possible Causes” listed above and visually inspect the related components.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1E63: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p1e63 fault code.
Here are the symptoms to look out for:
- The P1E63 fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience rough idling or stalling, and there may be a noticeable decrease in acceleration.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P1E63: Common Causes Of This Fault Code
P1E63 fault code can be caused by a faulty battery pack or battery interface control module in hybridelectric vehicles.
- The automobile fault code P1E63 can be caused by a faulty Hybrid/Electric Vehicle Battery Pack.
- It can also be caused by a faulty Hybrid/Electric Vehicle Battery Interface Control Module.
- These are the only two causes of this particular fault code.
Fix Code P1E63: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code p1e63, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code p1e63, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: P1E63 Fixing Cost & Complexity
The fault code P1E63 is a common issue in automobiles. The estimated repair time for this fault code is 1.0 hour.
The cost of fixing this fault code varies between $75 and $150 per hour, depending on the auto repair shop. The cost may also vary based on the severity of the issue and the type of repair required. It is important to get this fault code diagnosed and fixed as soon as possible to avoid any further damage to the vehicle.
P1E63: Your Car’s Battery Is In Trouble
The P1E63 code refers to a fault in the HybridElectric Vehicle Battery 56 Circuit.
The battery pack contains 288 cells grouped in parallel and series.
The battery energy control module monitors the voltage of the 96 battery cell groups through the four hybridEV battery interface control modules.
The battery energy control module will determine when a fault condition is present and communicate it to the hybridEV powertrain control module 2 through serial data. The hybridEV powertrain control module 2 is the host controller for diagnostic trouble code information.
The battery sections and their components are individually serviceable.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P1E63 fault code. This code is often caused by a faulty hybrid/electric vehicle battery pack or a faulty hybrid/electric vehicle battery interface control module. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P1E63 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, it could be caused by a faulty Hybrid/Electric Vehicle Battery Pack or a faulty Hybrid/Electric Vehicle Battery Interface Control Module. To fix this issue, you should check the possible causes listed above and visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
Ignoring the P1E63 fault code, which indicates a faulty hybrid/electric vehicle battery pack or interface control module, can lead to serious consequences such as reduced fuel efficiency, decreased power output, and even complete failure of the vehicle’s hybrid system. It is important to address the issue promptly by visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on, it could be due to a faulty hybridelectric vehicle battery pack or interface control module. Check the wiring harness and connectors for damage, broken, bent, pushed out, or corroded pins.
Inspect the components listed above to fix the issue.
