The P1E19 automobile fault code indicates a problem with the Power Inverter Module, which can cause the engine light to turn on. The cause of this issue could be a faulty module, an open or shorted harness, or a poor electrical connection. It is important to address this issue promptly as it can affect the performance of the vehicle.
The repair process involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector pins. The repair time for this issue is estimated to be around 1.0 hour.
To interpret the fault code, it is recommended to check the “Possible Causes” listed above.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1E19: Uncovering The Symptoms Of This Auto Fault Code
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the p1e19 fault code.
Here are the symptoms to look out for:
- The P1E19 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, poor acceleration, rough idling, stalling, and decreased fuel efficiency.
- Additionally, the vehicle may experience difficulty starting, and there may be a noticeable decrease in overall performance.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P1E19: Common Causes Of Fault Code
The P1E19 fault code in automobiles can be caused by a faulty power inverter module, open or shorted harness, or poor electrical connection.
- The automobile fault code P1E19 can be caused by a faulty Power Inverter Module.
- It can also be caused by an open or shorted Power Inverter Module harness.
- Additionally, a poor electrical connection in the Power Inverter Module circuit can also trigger this fault code.
Fix Code P1E19: Simple Steps To Get Your Car Running
To fix the p1e19 automobile fault code, check the possible causes and inspect the wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code P1E19, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: P1E19 Repair Cost & Complexity
The factors that influence the cost of diagnosing and fixing the automobile fault code P1E19 are the estimated repair time and the hourly rate charged by the auto repair shop.
The estimated repair time for this fault code is 1.0 hour.
The cost of labor varies between $75 and $150 per hour, depending on the auto repair shop.
These factors are crucial in determining the overall cost of diagnosing and fixing the P1E19 fault code.
P1E19: Your Car’s Battery Is In Trouble
The P1E19 code refers to the Auxiliary Transmission Fluid Pump Control Module System Voltage Low.
The power inverter module contains three motor control modules and the hybrid powertrain control module.
Two of the motor control modules operate their respective drive motor generator based upon power inverter module commands. The third motor control module controls the auxiliary transmission fluid pump motor. The hybrid powertrain control module and the motor control modules share the power inverter module ignition voltage circuit, battery voltage circuits and chassis earth.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P1E19 fault code. This code is usually caused by a faulty power inverter module, an open or shorted harness, or poor electrical connection in the power inverter module circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light due to a P1E19 fault code, you may need to visually inspect the related wiring harness and connectors. This is because the cause of the issue could be a faulty Power Inverter Module, an open or shorted Power Inverter Module harness, or a poor electrical connection in the Power Inverter Module circuit. To fix the problem, check the possible causes listed above and look for damaged components or broken, bent, pushed out, or corroded connector’s pins.
If you’re dealing with a P1E19 fault code, keep an eye out for the engine light or service engine soon warning light turning on. This is usually caused by a faulty power inverter module, an open or shorted harness, or poor electrical connection in the module circuit. To fix this, visually inspect the wiring harness and connectors, and check for damaged components or broken, bent, pushed out, or corroded connector pins.
Wrap Up
If your engine light is on, it could be due to a faulty power inverter module, an open or shorted harness, or poor electrical connection. Visually inspect the wiring harness and connectors for damage or corrosion.
Check for broken, bent, or pushed out pins.
