The P1E08 fault code in automobiles indicates a problem with the Power Inverter Module, which can trigger the Engine Light or Service Engine Soon Warning Light.
The possible causes of this issue include a faulty Power Inverter Module, an open or shorted harness, or poor electrical connections. To fix this problem, one should visually inspect the wiring harness and connectors for any damage or corrosion.
The repair time for this issue is estimated to be around 1.0. It is crucial to address this problem promptly to avoid further damage to the vehicle’s electrical system. To interpret the fault code, one can use an OBD-II scanner or take the vehicle to a professional mechanic.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1E08: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p1e08 fault code.
Here are the symptoms to look out for:
- The P1E08 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, poor acceleration, rough idling, stalling, and decreased fuel efficiency.
- Additionally, the vehicle may experience difficulty starting, and there may be a noticeable decrease in overall performance.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P1E08: What Triggers This Fault Code?
The P1E08 fault code can be caused by a faulty power inverter module, open or shorted harness, or poor electrical connection.
- The automobile fault code P1E08 can be caused by a faulty Power Inverter Module.
- It can also be caused by an open or shorted Power Inverter Module harness.
- Additionally, a poor electrical connection in the Power Inverter Module circuit can also trigger this fault code.
Fix Code P1E08: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code p1e08, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code p1e08, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: P1E08 Repair Cost & Complexity
The fault code P1E08 indicates an issue with the hybrid battery pack coolant pump. The estimated repair time for this issue is 1.0 hour.
The cost of fixing this issue can vary depending on the auto repair shop, but it is common for most shops to charge between $75 and $150 per hour. Other factors that may influence the cost include the severity of the issue, the type of vehicle, and the location of the repair shop.
P1E08: Your Car’s Battery Needs Attention
The P1E08 fault code is related to the hybrid powertrain control module. It monitors the high voltage contactor status of the hybridEV battery.
If there is a serial data fault, a redundant discreet circuit transmits the contactor requests to the hybrid powertrain control module 2 via a PWM signal. The code indicates a low voltage in the hybrid battery contactor status circuit. The hybrid powertrain control module is internal to the power inverter module and is not serviced separately.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P1E08 fault code. This code is usually caused by a faulty power inverter module, an open or shorted power inverter module harness, or a poor electrical connection in the power inverter module circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P1E08 fault code, start by checking the possible causes, which include a faulty power inverter module, an open or shorted power inverter module harness, or a poor electrical connection in the power inverter module circuit. To fix the issue, visually inspect the related wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
If you’re dealing with a P1E08 fault code, you may notice that your engine light is on or that the service engine soon warning light is illuminated. This is typically caused by a faulty power inverter module, an open or shorted harness, or a poor electrical connection in the power inverter module circuit. To fix the issue, start by visually inspecting the wiring harness and connectors, checking for any damaged components or broken, bent, pushed out, or corroded connector pins.
Wrap Up
If your engine light is on, it could be due to a faulty power inverter module, an open or shorted harness, or poor electrical connection.
Visually inspect the wiring harness and connectors for damage or corrosion.
Check for broken, bent, or pushed out pins.
