If you see the engine light on or the service engine soon warning light, it could be due to the P1CCE fault code.
This code indicates a problem with the Smart Drive Unit (SDU) or the Transmission Controller Module (TCM). The cause could be a faulty SDU, an open or shorted SDU harness, or a poor electrical connection in the SDU circuit.
The repair importance is high as it can affect the performance of the vehicle.
The repair difficulty is moderate, and it may take around 1.0 hour to fix.
To interpret the fault code, check the possible causes listed above and visually inspect the related wiring harness and connectors.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1Cce: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be due to the p1cce fault code.
Here are the symptoms to look out for:
- The P1CCE fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, engine stalling, rough idling, decreased fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience transmission shifting issues, and there may be a noticeable decrease in overall performance.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
Decoding P1Cce: Common Causes Of This Fault Code
The P1CCE automobile fault code can be caused by a faulty SDU, SDU harness issues, or a faulty TCM.
- The automobile fault code P1CCE can be caused by a faulty Smart Drive Unit (SDU).
- It can also be caused by an open or shorted SDU harness.
- Poor electrical connection in the SDU circuit can also trigger this fault code.
- Lastly, a faulty Transmission Controller Module (TCM) can also be a cause of the P1CCE fault code.
Fix Code P1Cce: Simple Steps To Get Your Car Running
Below are some possible fixes for the automobile fault code p1cce, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code p1cce, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P1Cce: Affordable Fix For Complex Automobile Fault Code
The automobile fault code P1CCE has an estimated repair time of 1.0 hour. The cost of fixing this fault code is based on the repair time. Most auto repair shops charge between $75 and $150 per hour for repairs.
Therefore, the cost of fixing the P1CCE fault code will be influenced by the hourly rate charged by the repair shop.
It is important to consider this factor when estimating the total cost of repairing the P1CCE fault code.
P1Cce: Your Car’s Fuel System Needs Attention
The P1CCE fault code is related to the hydraulic pump driver feedback range performance. It is a diagnostic check that verifies the range of the hydraulic pump driver feedback signal provided by the Smart Drive Unit (SDU) to the Transmission Control Module (TCM). The normal range of the hydraulic pump driver feedback signal is up to 30% of the power supply voltage.
If the signal falls outside of this range, the P1CCE code will be triggered, indicating an issue with the hydraulic pump driver feedback range performance.
FAQ
If you notice the engine light ON or Service Engine Soon Warning Light, it could be due to the P1CCE fault code. This code can be caused by a faulty Smart Drive Unit (SDU), an open or shorted SDU harness, a poor electrical connection in the SDU circuit, or a faulty Transmission Controller Module (TCM). To identify the cause, visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P1CCE fault code, indicated by the engine light or service engine soon warning light being on, it may be due to a faulty Smart Drive Unit (SDU). To fix this issue, start by checking the possible causes listed above. Inspect the wiring harness and connectors for any damage or corrosion, and check for broken or bent pins.
To visually inspect the wiring harness and connectors related to the P1CCE fault code, check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. Check the “Possible Causes” listed above and visually inspect the related wiring harness and connectors.
Wrap Up
If your engine light is on, it could be due to a faulty Smart Drive Unit (SDU), an open or shorted SDU harness, a poor electrical connection in the SDU circuit, or a faulty Transmission Controller Module (TCM). To fix the issue, visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
