The P1CC8 automobile fault code is a common issue that triggers the Engine Light ON or Service Engine Soon Warning Light.
The code is caused by a low battery charge, faulty Transmission Controller Module (TCM), or poor electrical connection in the TCM circuit.
The importance of repairing this issue lies in the fact that it can lead to serious transmission problems if left unaddressed.
The repair difficulty is moderate, with a repair time of 1.0. To fix the issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
It is crucial to check the “Possible Causes” listed above to interpret the fault code correctly.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
P1Cc8: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p1cc8 fault code. Here are the symptoms to look out for:
- The P1CC8 fault code in an automobile can cause several symptoms.
- The most common symptom is the illumination of the engine light or service engine soon warning light.
- Other symptoms include reduced engine power, poor acceleration, rough idling, stalling, and decreased fuel efficiency.
- Additionally, the vehicle may experience difficulty starting, and there may be a noticeable decrease in overall performance.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P1Cc8: Common Causes
The P1CC8 fault code in automobiles can be caused by a variety of factors, including low battery charge and faulty TCM.
- The automobile fault code P1CC8 can be caused by a low battery charge.
- Another cause of this fault code is a faulty Transmission Controller Module (TCM).
- An open or shorted Transmission Controller Module (TCM) harness can also trigger this fault code.
- Lastly, a poor electrical connection in the Transmission Controller Module (TCM) circuit can cause the P1CC8 fault code to appear.
Fix Code P1Cc8: Simple Steps To Get Your Car Running
To fix the p1cc8 fault code, check the possible causes and inspect the wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p1cc8, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P1Cc8: Affordable Fix For Your Car
The fault code P1CC8 indicates a problem with the hybrid battery coolant pump control circuit. The estimated repair time for this issue is 1.0 hour. The cost of fixing this issue can vary depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour.
Other factors that may influence the cost include the severity of the issue, the type of vehicle, and the location of the repair shop.
P1Cc8: Your Car’s Battery Is In Trouble
The P1CC8 fault code is related to the power supply of the Main Micro Processor (MMP) in a vehicle. This diagnostic test checks the MMP power supply with three different tests under different vehicle operating conditions.
If the actual value of power supply is below its minimum boundary, the diagnostic will be considered failing.
The TCM verifies the MMP power supply is not lower than a threshold for more than an amount of time after the engine cranking mode is finished plus a time delay.
The TCM also verifies the MMP power supply is not lower than a threshold for more than an amount of time after the engine cranking mode is finished plus a time delay only when the hydraulic pump is on for more than a time and the pump temperature is lower than a value.
FAQ
If you’re experiencing the P1CC8 fault code, your engine light may be on. This could be due to a low battery charge, a faulty Transmission Controller Module (TCM), an open or shorted TCM harness, or a poor electrical connection in the TCM circuit. To identify the cause, visually inspect the wiring harness and connectors for any damage or corrosion. Check for broken, bent, or pushed out connector pins.
A low battery charge can contribute to the P1CC8 fault code, resulting in the engine light turning on. To prevent this, regularly check the battery charge and ensure it is fully charged. Additionally, inspect the wiring harness and connectors for any damage or corrosion. Check for broken, bent, or pushed out connector pins and replace any faulty components.
If the P1CC8 fault code is detected, the engine light may turn on. The possible causes include low battery charge, a faulty Transmission Controller Module (TCM), an open or shorted TCM harness, or a poor electrical connection in the TCM circuit. To fix the issue, visually inspect the related wiring harness and connectors for any damaged components, broken, bent, pushed out, or corroded connector’s pins. Check the “Possible Causes” listed above to determine the root cause of the problem.
![p1cc8 error fault code explained](https://carmodnerd.com/wp-content/uploads/2023/06/P1CC8-error-fault-code.jpg)
Wrap Up
If your engine light is on, it could be due to low battery charge, a faulty TCM, or poor electrical connection. Check the wiring harness and connectors for damage and inspect the components for any issues.
Take action based on the possible causes listed above.