The P1BFE automobile fault code indicates a problem with the HybridElectric Vehicle Battery Pack or the HybridElectric Vehicle Battery Interface Control Module. The most common symptom is the Engine Light turning on. It is crucial to address this issue promptly as it can lead to further damage to the vehicle.
The repair difficulty is moderate, and the repair time is estimated at 1.0 hour. To fix the issue, one must visually inspect the wiring harness and connectors for any damage or corrosion. It is also recommended to check for broken, bent, or pushed out connector pins.
It is essential to interpret the fault code accurately to ensure the correct repair is performed.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1Bfe: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p1bfe fault code.
Here are the symptoms to look out for:
- The P1BFE fault code in automobiles can cause the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding P1Bfe: Common Causes Of The Fault Code
The P1BFE automobile fault code can be caused by a faulty battery pack or battery interface control module.
- The automobile fault code P1BFE can be caused by a faulty Hybrid/Electric Vehicle Battery Pack.
- It can also be caused by a faulty Hybrid/Electric Vehicle Battery Interface Control Module.
- These are the only two causes of the P1BFE fault code.
Fix Code P1Bfe: Simple Steps To Get Your Car Running
To fix the p1bfe automobile fault code, check the possible causes and inspect related components for damage or corrosion.
- To fix the automobile fault code p1bfe, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: P1Bfe Repair Cost & Complexity
The fault code P1BFE is a common issue in automobiles. The estimated repair time for this fault code is 1.0 hour. The cost of fixing this fault code is dependent on the repair time.
Most auto repair shops charge between $75 and $150 per hour.
Therefore, the cost of fixing the P1BFE fault code can range from $75 to $150.
It is important to consider the repair time and the hourly rate when estimating the cost of fixing this fault code.
P1Bfe: The Low Pressure Fuel System Sensor Circuit Range/Performance
The P1BFE code is related to the HybridElectric Vehicle battery pack.
The battery pack contains 288 cells grouped in parallel and in-series. There are three battery sections, each with a different number of cells and cell groups. The battery energy control module monitors the voltage of the 96 battery cell groups through the hybridEV battery interface control modules.
The battery energy control module will determine when a fault condition is present and communicate it to the hybridEV powertrain control module 2. The P1BFE code indicates a high voltage circuit issue in the HybridElectric Vehicle battery 94.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P1BFE fault code. This code is usually caused by a faulty hybrid/electric vehicle battery pack or a faulty hybrid/electric vehicle battery interface control module. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P1BFE fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, you may have a faulty Hybrid/Electric Vehicle Battery Pack or a faulty Hybrid/Electric Vehicle Battery Interface Control Module. To fix this issue, start by visually inspecting the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues and determine the best course of action to take.
If you notice the engine light or service engine soon warning light on, it could be a sign of a faulty Hybrid/Electric Vehicle Battery Interface Control Module. This fault code, P1BFE, can be caused by a faulty Hybrid/Electric Vehicle Battery Pack or a faulty Hybrid/Electric Vehicle Battery Interface Control Module. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on, it could be due to a faulty hybridelectric vehicle battery pack or interface control module.
Check the possible causes, inspect wiring harness and connectors, and look for damaged components or corroded pins.
