The P1BA0 automobile fault code indicates a problem with the HybridElectric Vehicle Battery Pack or the Battery Interface Control Module.

The most common symptom is the Engine Light turning on. The cause of this issue is usually a faulty battery pack or control module. It is important to address this issue promptly as it can lead to further damage to the vehicle.

The repair difficulty is moderate, and the repair time is estimated at 1.0 hour.

To fix the problem, one should visually inspect the wiring harness and connectors for any damage or corrosion. It is also recommended to check for broken, bent, or pushed out connector pins.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p1ba0 fault code.

Here are the symptoms to look out for:

  • The P1BA0 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
  • Other symptoms may include reduced engine power, decreased fuel efficiency, and difficulty starting the engine.
  • Additionally, the vehicle may experience rough idling or stalling, and there may be a noticeable decrease in acceleration.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.

The P1BA0 fault code can be caused by a faulty battery pack or battery interface control module in hybridelectric vehicles.

  • The automobile fault code P1BA0 can be caused by a faulty Hybrid/Electric Vehicle Battery Pack.
  • It can also be caused by a faulty Hybrid/Electric Vehicle Battery Interface Control Module.
  • These are the only two causes of the P1BA0 fault code.

Below are the possible fixes for the automobile fault code p1ba0, including inspecting wiring harness and connectors for damage or corrosion.

  • To fix the automobile fault code p1ba0, you need to check the possible causes listed above.
  • Visually inspect the related wiring harness and connectors.
  • Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The fault code P1BA0 indicates a problem with the hybrid battery pack coolant pump. The estimated repair time for this issue is 1.0 hour. The cost of fixing this issue can vary depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour.

Other factors that may influence the cost include the severity of the issue, the type of vehicle, and the location of the repair shop.

It is important to address this issue promptly to avoid further damage to the hybrid battery pack.

The P1BA0 code indicates a low voltage in the HybridElectric Vehicle Battery 63 Circuit. The battery pack contains 288 cells grouped in parallel and connected in-series.

The battery energy control module monitors the voltage of the 96 battery cell groups through the hybridEV battery interface control modules. The battery energy control module communicates diagnostics and system status to the hybridEV powertrain control module 2.

The hybridEV powertrain control module 2 is the host controller for diagnostic trouble code information.

What are the possible causes of the P1BA0 automobile fault code?

If you see the engine light on or the service engine soon warning light, it could be due to the P1BA0 fault code. This code is usually caused by a faulty hybrid/electric vehicle battery pack or a faulty hybrid/electric vehicle battery interface control module. To fix this issue, you should check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for any damaged components or broken, bent, pushed out, or corroded connector’s pins.

How can I visually inspect the related wiring harness and connectors to fix the P1BA0 fault code?

If you’re experiencing the P1BA0 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, you may have a faulty Hybrid/Electric Vehicle Battery Pack or a faulty Hybrid/Electric Vehicle Battery Interface Control Module. To fix this issue, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues and determine the best course of action to take.

What are the signs of damaged components that I should look for when fixing the P1BA0 fault code?

If you’re fixing the P1BA0 fault code, keep an eye out for the engine light or service engine soon warning light. The possible causes are a faulty hybrid/electric vehicle battery pack or a faulty hybrid/electric vehicle battery interface control module. To fix it, visually inspect the related wiring harness and connectors for any damaged components. Check for broken, bent, pushed out, or corroded connector’s pins.

p1ba0 error fault code explained

If your engine light is on, it could be due to a faulty hybridelectric vehicle battery pack or interface control module.

Check the wiring harness and connectors for damage, broken or corroded pins. Inspect the components listed under “Possible Causes” to fix the issue.

Scroll to Top