The P1B76 automobile fault code indicates a problem with the HybridElectric Vehicle Battery Pack or the HybridElectric Vehicle Battery Interface Control Module.
The most common symptom is the Engine Light ON or Service Engine Soon Warning Light.
The importance of repairing this issue lies in the fact that it can affect the performance and efficiency of the vehicle. The difficulty level of the repair is moderate, and it can take up to 1.0 hour to fix.
To interpret the fault code, one needs to check the possible causes listed above and visually inspect the related wiring harness and connectors for any damage or corrosion.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1B76: Uncovering The Symptoms Of This Auto Fault Code
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the p1b76 fault code.
Here are the symptoms to look out for:
- The P1B76 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include issues with the transmission, such as difficulty shifting gears or the transmission slipping.
- The vehicle may also experience reduced power or acceleration, and the engine may stall or hesitate during operation.
- Additionally, the fuel efficiency of the vehicle may decrease, and there may be a noticeable decrease in overall performance.
Decoding P1B76: Common Causes Of This Fault Code
P1B76 fault code can be caused by a faulty battery pack or battery interface control module in hybridelectric vehicles.
- The automobile fault code P1B76 can be caused by a faulty Hybrid/Electric Vehicle Battery Pack.
- It can also be caused by a faulty Hybrid/Electric Vehicle Battery Interface Control Module.
- These are the only two causes of the P1B76 fault code.
Fix Code P1B76: Quick Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code p1b76, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code P1B76, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P1B76: Affordable Fix For Your Car’s Electrical System
The fault code P1B76 indicates a problem with the Hybrid Battery Pack Voltage Sensor Circuit. The estimated repair time for this fault is 1.0 hour. The cost of fixing this fault will depend on the hourly rate charged by the auto repair shop.
The average hourly rate is between $75 and $150.
Therefore, the cost of fixing this fault can range from $75 to $150.
P1B76: Your Car’s Battery Needs Attention
The P1B76 code is related to the HybridElectric Vehicle battery pack.
The battery pack contains 288 cells grouped in parallel and series. There are three battery sections, each with a different number of cells.
The battery energy control module monitors the voltage of the 96 battery cell groups.
The hybridEV powertrain control module 2 is the host controller for diagnostic trouble code information.
The P1B76 code indicates a low voltage condition in the HybridElectric Vehicle Battery 49 Circuit.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P1B76 fault code. This code is caused by a faulty hybrid/electric vehicle battery pack or a faulty hybrid/electric vehicle battery interface control module. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P1B76 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light, it could be caused by a faulty Hybrid/Electric Vehicle Battery Pack or a faulty Hybrid/Electric Vehicle Battery Interface Control Module. To fix this issue, you should check the possible causes listed above and visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
Ignoring the P1B76 fault code, which indicates a faulty hybrid/electric vehicle battery pack or interface control module, can lead to serious consequences such as reduced fuel efficiency, decreased power output, and even complete failure of the vehicle’s hybrid system. It is important to address the issue promptly by visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on, it could be due to a faulty hybridelectric vehicle battery pack or interface control module. Check the wiring harness and connectors for damage, broken or corroded pins.
Inspect the components listed above to fix the issue.
