The P1B0C automobile fault code indicates a problem with the Drive Motor 1 Control Module HybridEV Battery. The most common symptom is the Engine Light ON or Service Engine Soon Warning Light. The cause of this issue could be a faulty control module, an open or shorted harness, or a poor electrical connection.
The repair importance is high as it affects the performance of the vehicle.
The difficulty level of the repair is moderate, and it takes around 1.0 hour to fix.
To interpret the fault code, one needs to check the possible causes listed above and visually inspect the related wiring harness and connectors.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1B0C: Uncovering The Symptoms Of This Auto Fault Code
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the p1b0c fault code. Here are the symptoms to look out for:
- The P1B0C fault code in automobiles can cause the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding P1B0C: Common Causes Of This Fault Code
The P1B0C automobile fault code can be caused by various issues, including a faulty drive motor control module and poor electrical connections.
- The automobile fault code P1B0C can be caused by a faulty Drive Motor 1 Control Module Hybrid/EV Battery.
- It can also be caused by an open or shorted Drive Motor 1 Control Module Hybrid/EV Battery harness.
- Additionally, a poor electrical connection in the Drive Motor 1 Control Module Hybrid/EV Battery circuit can also trigger this fault code.
Fix Code P1B0C: Simple Steps To Get Your Car Running
To fix the p1b0c automobile fault code, check the possible causes and inspect the wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p1b0c, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: P1B0C Fixing Cost & Complexity
The automobile fault code P1B0C has an estimated repair time of 1.0 hour.
The cost of fixing this fault code is influenced by the repair time.
Most auto repair shops charge between $75 and $150 per hour for their services.
Therefore, the fixing cost of P1B0C will depend on the hourly rate charged by the repair shop.
It is important to consider these factors when budgeting for the repair of this fault code.
P1B0C: Decoding The Mysterious Fault In Your Automobile
The P1B0C fault code relates to the power inverter module in a hybrid vehicle. It contains two motor control modules that measure hybrid battery high voltage. Loss of isolation between high-voltage circuits and vehicle chassis is tested when high-voltage contactor relays are closed.
Motor control module loss of isolation is detected through two high-impedance resistors and voltage measuring circuitry.
The motor isolation voltage display will indicate voltage that is more or less than actual hybrid battery high voltage when a loss of isolation is present.
FAQ
If you’re experiencing the P1B0C fault code in your automobile, you may notice that the engine light is on or the service engine soon warning light is illuminated. This fault code is typically caused by a faulty drive motor 1 control module hybrid/EV battery, an open or shorted harness, or a poor electrical connection in the drive motor 1 control module hybrid/EV battery circuit. To fix this issue, it’s important to visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If the Engine Light or Service Engine Soon Warning Light is on, it could be due to a faulty Drive Motor 1 Control Module Hybrid/EV Battery. To fix this, check for possible causes such as an open or shorted harness or poor electrical connection. To visually inspect the related wiring harness and connectors, look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
If you encounter the P1B0C fault code in your automobile, with the engine light ON or Service Engine Soon Warning Light, you should check for a faulty Drive Motor 1 Control Module Hybrid/EV Battery, an open or shorted Drive Motor 1 Control Module Hybrid/EV Battery harness, or a poor electrical connection in the Drive Motor 1 Control Module Hybrid/EV Battery circuit. To fix this issue, visually inspect the related wiring harness and connectors, and check for damaged components. Look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on, it could be due to a faulty Drive Motor 1 Control Module HybridEV Battery. Check the wiring harness and connectors for any damage or poor electrical connections.
Look for broken, bent, pushed out, or corroded connector’s pins.
