The P1B06 automobile fault code indicates a problem with the Drive Motor Generator Power Inverter Module, which can cause the engine light to turn on. The possible causes include a faulty module, an open or shorted harness, or a poor electrical connection. It is important to visually inspect the wiring harness and connectors for any damage or corrosion.
The repair time for this issue is estimated at 1.0, and it is crucial to address the problem promptly to avoid further damage to the vehicle.
To interpret the fault code, it is recommended to check the “Possible Causes” listed above and inspect the related components thoroughly.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1B06: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p1b06 fault code. Here are the symptoms to look out for:
- The P1B06 fault code in an automobile can cause the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding P1B06: Common Causes Of This Fault Code
The P1B06 automobile fault code can be caused by a faulty drive motor generator power inverter module, an open or shorted harness, or poor electrical connection.
- The automobile fault code P1B06 can be caused by a faulty Drive Motor Generator Power Inverter Module.
- It can also be caused by an open or shorted harness of the Drive Motor Generator Power Inverter Module.
- Additionally, a poor electrical connection in the circuit of the Drive Motor Generator Power Inverter Module can also trigger this fault code.
Fix Code P1B06: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code p1b06, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code P1B06, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: P1B06 Repair Cost & Complexity
The factors that influence the cost of diagnosing and fixing the P1B06 automobile fault code based on the estimated repair time of 1.0 hour are: – The hourly rate charged by the auto repair shop, which can range from $75 to $150 per hour. – The complexity of the repair required to fix the fault code. – The availability and cost of replacement parts needed for the repair. – The experience and expertise of the mechanic performing the repair. – The location of the auto repair shop, as labor rates can vary by region.
P1B06: Understanding Your Car’s Brake Booster Pressure Sensor Issue
The P1B06 code is related to the high voltage interlock circuit in an automobile. This circuit is used to verify the integrity of high voltage components.
It passes through certain high voltage components and detects any attempt to access them.
If the circuit detects an open condition, the high voltage contactor relays are commanded open by the hybrid powertrain control module. Both motor control modules monitor the circuit for current to detect any faults. The battery energy control module sources about 12 mA of current on the 5V high voltage interlock circuit loop.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P1B06 fault code. This code is caused by a faulty drive motor generator power inverter module, an open or shorted harness, or a poor electrical connection in the module circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Drive Motor Generator Power Inverter Module or an open or shorted harness. To fix this issue, you should visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any poor electrical connections and ensure that your Drive Motor Generator Power Inverter Module is functioning properly.
If you find broken, bent, pushed out, or corroded connector’s pins while inspecting the related components, it could be the cause of the Engine Light ON (or Service Engine Soon Warning Light) symptom. To fix this issue, check the “Possible Causes” listed above and visually inspect the related wiring harness and connectors. Look for damaged components and examine the connector’s pins for any signs of damage. If you find any issues, replace or repair the damaged components and pins to ensure a proper electrical connection.
Wrap Up
If your engine light is on, it could be due to a faulty Drive Motor Generator Power Inverter Module or related wiring issues. Check for damaged components and inspect the wiring harness and connectors for any issues.
Look for broken, bent, pushed out, or corroded connector’s pins.
