The P1AF6 automobile fault code is a common issue that triggers the Engine Light ON or Service Engine Soon Warning Light. The cause of this fault code could be due to a faulty Power Inverter Control Module (PIM), an open or shorted PIM harness, or a poor electrical connection in the PIM circuit. The importance of repairing this issue lies in the fact that it affects the performance of the vehicle.
The difficulty level of repairing this issue is moderate, and it takes approximately 1.0 hour to fix. To interpret the fault code, one needs to check the possible causes listed above and visually inspect the related wiring harness and connectors.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1Af6: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p1af6 fault code.
Here are the symptoms to look out for:
- The P1AF6 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience rough idling or stalling, and there may be a noticeable decrease in acceleration.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P1Af6: Common Causes
The P1AF6 automobile fault code can be caused by various factors, including a faulty PIM or poor electrical connection.
- The automobile fault code P1AF6 can be caused by a faulty Power Inverter Control Module (PIM), an open or shorted PIM harness, poor electrical connection in the PIM circuit, or the need to reprogram the PIM.
Fix Code P1Af6: Simple Steps To Get Your Car Running
To fix the p1af6 fault code, check the possible causes and inspect the wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p1af6, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P1Af6: Affordable Fix For Complex Automobile Fault Code
The automobile fault code P1AF6 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops. Therefore, the total cost of diagnosis and fixing the P1AF6 fault code will depend on the hourly rate charged by the repair shop and the time taken to complete the repair.
P1Af6: The Low Voltage Battery Heater Control Circuit – Explained
The P1AF6 code is related to the Drive Motor 2 Control Module.
It indicates a problem with the Hybrid Battery Voltage Isolation Sensor Circuit. The Motor Control Modules (MCMs) test for Loss of Isolation (LOI) between the HV circuits and vehicle chassis. The MCM measures the voltage drop across one of the resistors to detect LOI.
Without a loss of isolation, the MCM should measure about half of the high voltage potential. The Mid-pack voltage value is then doubled by the software and displayed on a scan tool as Motor 1 Isolation Voltage or Motor 2 Isolation Voltage. When a loss of isolation is present, the motor isolation voltage display will indicate voltage that is more or less than actual hybrid battery high voltage.
FAQ
If you see the engine light on or service engine soon warning light in your automobile, it could be due to the P1AF6 fault code. This code can be caused by a faulty power inverter control module (PIM), an open or shorted PIM harness, or a poor electrical connection in the PIM circuit. To fix this issue, you should reprogram the PIM and visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P1AF6 fault code in your automobile, you may notice the engine light is on. The cause of this issue could be a faulty Power Inverter Control Module (PIM), an open or shorted PIM harness, or a poor electrical connection. To fix this issue, check the possible causes listed above, visually inspect the wiring harness and connectors, and look for any damaged components or broken, bent, pushed out, or corroded connector pins.
If you’re trying to fix the P1AF6 fault code in your automobile, start by checking for the symptom of the engine light being on. The cause could be a faulty power inverter control module (PIM), an open or shorted PIM harness, or poor electrical connection in the PIM circuit. To fix the issue, visually inspect the wiring harness and connectors for any damage or broken, bent, pushed out, or corroded pins. Check the “Possible Causes” listed above for more information.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light with the fault code P1AF6, check the Power Inverter Control Module (PIM) and its related wiring harness and connectors for any damage or poor electrical connection.
Reprogram or replace the PIM as necessary.
