The P1AEA automobile fault code indicates a problem with the Drive Motor Generator Power Inverter Module, which can cause the engine light to turn on.
The possible causes include a faulty module, an open or shorted harness, or poor electrical connections. It is important to visually inspect the wiring harness and connectors for any damage or corrosion. The repair time for this issue is estimated at 1.0, and it is crucial to address the problem promptly to avoid further damage to the vehicle.
To interpret the fault code, it is recommended to check the “Possible Causes” listed above and inspect the related components thoroughly.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1Aea: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p1aea fault code.
Here are the symptoms to look out for:
- The P1AEA fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, rough idling, stalling, and difficulty starting the engine.
- Additionally, the vehicle may experience misfires, hesitation, or surging during acceleration.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P1Aea: Common Causes Of This Fault Code
P1AEA fault code can be caused by various issues such as faulty drive motor generator power inverter module or poor electrical connection.
- The automobile fault code P1AEA can be caused by a faulty Drive Motor Generator Power Inverter Module.
- It can also be caused by an open or shorted harness of the Drive Motor Generator Power Inverter Module.
- Additionally, a poor electrical connection in the circuit of the Drive Motor Generator Power Inverter Module can also trigger this fault code.
Fix P1Aea: Simple Steps To Solve The Fault Code
Below are the possible fixes for the automobile fault code p1aea, including a visual inspection of wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p1aea, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded connector’s pins.
- Estimated repair time for this fix is 1.0 hour.
Crunching The Numbers: Fixing P1Aea Code Complexity & Cost
The fault code P1AEA is a diagnostic trouble code related to the hybrid battery pack. The code indicates that the battery pack has an internal malfunction. The estimated repair time for this fault code is 1.0 hour.
The cost of fixing this issue can vary depending on the auto repair shop, but it is common for most shops to charge between $75 and $150 per hour. Other factors that can influence the cost of fixing this issue include the severity of the problem, the type of vehicle, and the location of the repair shop.
P1Aea: Your Car’s Oxygen Sensor Needs Attention
The P1AEA code is related to the Drive Motor Generator Power Inverter Module. This module contains two drive motor control modules that monitor their internal high voltage sensor for correct operation.
The code indicates that there is an issue with the Hybrid Battery Voltage Sense Circuit of Drive Motor 2 Control Module, which is causing low voltage.
The modules listed, including the Hybrid powertrain control module, Motor control module 1, and Motor control module 2, are part of the Drive Motor Generator Power Inverter Module and are not serviced separately.
FAQ
If you see the engine light on or the service engine soon warning light in your automobile, it could be due to the P1AEA fault code. This fault code is caused by a faulty drive motor generator power inverter module, an open or shorted harness, or a poor electrical connection in the drive motor generator power inverter module circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P1AEA fault code in your automobile, you may notice the engine light or service engine soon warning light is on. This is likely due to a faulty drive motor generator power inverter module, an open or shorted harness, or poor electrical connection. To fix the issue, visually inspect the wiring harness and connectors for any damage or corrosion. Check for broken, bent, pushed out, or corroded connector pins.
If you’re trying to fix the P1AEA fault code in your automobile, start by visually inspecting the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins. This fault code is usually caused by a faulty Drive Motor Generator Power Inverter Module or an open or shorted circuit with poor electrical connection. Check the “Possible Causes” listed above for more information.
Wrap Up
If your engine light is on, it could be due to a faulty Drive Motor Generator Power Inverter Module or related wiring issues. Check for damaged components and inspect the wiring harness and connectors for any issues.
Look for broken, bent, pushed out, or corroded connector’s pins.
