If you see the engine light on or the service engine soon warning light, it could be due to a fault code P1A6A. This code indicates a problem with the StarterGenerator Control Module (SGCM) or its related wiring harness and connectors.
The cause could be a faulty SGCM, an open or shorted harness, or poor electrical connection. It is important to address this issue promptly as it can affect the performance of your vehicle.
The repair time for this fault code is 1.0, and the fix involves visually inspecting the wiring harness and connectors for any damage or corrosion.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1A6A: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON, it could be a sign of p1a6a fault code.
Here are the symptoms to look out for:
- The P1A6A fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience rough idling or stalling, and there may be a noticeable decrease in acceleration.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P1A6A: Common Causes
The P1A6A automobile fault code can be caused by various factors, including a faulty SGCM, open or shorted harness, and poor electrical connection.
- The automobile fault code P1A6A can be caused by a faulty Starter/Generator Control Module (SGCM).
- It can also be caused by an open or shorted Starter/Generator Control Module harness.
- Additionally, a poor electrical connection in the Starter/Generator Control Module circuit can also trigger this fault code.
Fix Code P1A6A: Simple Steps To Get Your Car Running
To fix the p1a6a automobile fault code, check the possible causes and inspect the wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p1a6a, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: P1A6A Fixing Cost And Complexity
The automobile fault code P1A6A has an estimated repair time of 1.0 hour. The cost of fixing this fault code is influenced by the repair time.
Most auto repair shops charge between $75 and $150 per hour for their services. Therefore, the fixing cost of P1A6A will be between $75 and $150, depending on the repair time required.
P1A6A: Understanding Your Car’s Battery Temperature Sensor Fault
The P1A6A fault code is related to the StarterGenerator Control Module (SGCM).
The Accessory Power Module (APM) is integral to the SGCM and controls the energy flow between the 42 V DC and 14 V DC buses. The APM functions only when in enable mode and its power is bi-directional.
Negative current represents 14-42 direction, and positive current represents the 42-14 direction. When the APM Power Conversion direction is set to Off, it will not consume or transfer any power.
When the APM Power Conversion direction is set to Invalid, the energy will flow from the 42 V DC Bus to the 14 V DC Bus via the APM.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P1A6A fault code. This code is caused by a faulty Starter/Generator Control Module (SGCM), an open or shorted SGCM harness, or a poor electrical connection in the SGCM circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light due to a P1A6A fault code, it may be caused by a faulty Starter/Generator Control Module (SGCM), an open or shorted SGCM harness, or a poor electrical connection in the SGCM circuit. To fix this issue, visually inspect the related wiring harness and connectors for any damaged components, broken, bent, pushed out, or corroded connector’s pins. Check the “Possible Causes” listed above for further guidance.
The P1A6A fault code in an automobile is indicated by the Engine Light ON or Service Engine Soon Warning Light. The possible causes of this fault code are a faulty Starter/Generator Control Module (SGCM), an open or shorted SGCM harness, or a poor electrical connection in the SGCM circuit. To fix this issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on, it could be due to a faulty StarterGenerator Control Module (SGCM), an open or shorted harness, or poor electrical connection. Visually inspect the wiring harness and connectors for damage and check for broken, bent, pushed out, or corroded connector pins to fix the issue.
