The P1A35 fault code in automobiles indicates a problem with the Energy Storage Box (ESB) Battery or the Battery Energy Control Module (BECM). The most common symptom is the illumination of the Engine Light or Service Engine Soon Warning Light. The cause of this fault code could be a faulty ESB battery, BECM, or an open or shorted BECM harness.
The repair importance is high as it affects the performance of the vehicle. The repair difficulty is moderate, and the fix involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins.
The repair time is estimated to be 1.0 hour.
It is essential to check the possible causes listed above to interpret the fault code accurately.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P1A35: Uncovering The Symptoms Of This Auto Fault Code
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p1a35 fault code.
Here are the symptoms to look out for:
- The P1A35 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include reduced engine power, decreased fuel efficiency, and difficulty starting the engine.
- Additionally, the vehicle may experience rough idling or stalling, and there may be a noticeable decrease in acceleration.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
Decoding P1A35: Common Causes Of Fault Code
The P1A35 fault code in automobiles can be caused by various factors, including a faulty ESB battery, BECM module, harness, or poor electrical connection.
- The automobile fault code P1A35 can be caused by a faulty Energy Storage Box (ESB) Battery.
- It can also be caused by a faulty Battery Energy Control Module (BECM).
- Another cause of this fault code is when the Battery Energy Control Module (BECM) harness is open or shorted.
- Lastly, a poor electrical connection in the Battery Energy Control Module (BECM) circuit can also cause this fault code.
Fix Code P1A35: Simple Steps To Get Your Car Running
Below are some possible fixes for the automobile fault code p1a35, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code P1A35, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P1A35: Affordable Fix For Complex Automobiles
The factors that influence the cost of diagnosing and fixing the automobile fault code P1A35 include the estimated repair time, which is 1.0 hour. The cost of repair is also influenced by the hourly rate charged by the auto repair shop, which is typically between $75 and $150 per hour. These factors should be considered when estimating the total cost of diagnosing and fixing the P1A35 fault code.
P1A35: The Low Voltage Battery Heater Control Circuit – Explained
The P1A35 code is related to the hybrid battery voltage. It indicates that the voltage of the third battery in the Energy Storage Box (ESB) is very low. The Energy Storage Control Module (ESCM) uses battery voltage sensors to monitor the voltage of the batteries in the ESB.
The ESCM monitors the voltage drop across the battery voltage sensors and uses the inputs for hybrid calculations. When the battery voltage is low, the resistances of the sensors are low and the voltage signals are low.
The P1A35 code can be caused by a faulty battery or a problem with the battery voltage sensors. It is important to address this issue promptly to avoid further damage to the hybrid system.
FAQ
If you’re experiencing the P1A35 fault code in your automobile, you may notice that the engine light is on or the service engine soon warning light is illuminated. This fault code is typically caused by a faulty Energy Storage Box (ESB) battery, a faulty Battery Energy Control Module (BECM), an open or shorted BECM harness, or a poor electrical connection in the BECM circuit. To fix the issue, it’s important to visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light due to a P1A35 fault code, there are a few possible causes. These include a faulty Energy Storage Box (ESB) Battery, a faulty Battery Energy Control Module (BECM), an open or shorted BECM harness, or a poor electrical connection in the BECM circuit. To fix the issue, start by visually inspecting the related wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
The P1A35 fault code in an automobile is indicated by the Engine Light ON or Service Engine Soon Warning Light. The possible causes of this fault code are a faulty Energy Storage Box (ESB) Battery, a faulty Battery Energy Control Module (BECM), an open or shorted BECM harness, or a poor electrical connection in the BECM circuit. To fix this issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on and the code is P1A35, it could be due to a faulty Energy Storage Box (ESB) battery, Battery Energy Control Module (BECM), or poor electrical connection.
Visually inspect the wiring harness and connectors for damage and check for broken or corroded pins.
