The automobile fault code P1317 indicates a problem with the ABS Speed Sensor. The most common symptom is the Engine Light being ON or the Service Engine Soon Warning Light. The cause of this fault code can be a faulty ABS Speed Sensor, an open or shorted ABS Speed Sensor harness, a poor electrical connection in the ABS Speed Sensor circuit, or a faulty Engine Control Module (ECM).
To fix this issue, you should visually inspect the wiring harness and connectors, checking for any damage or broken, bent, pushed out, or corroded pins.
The repair time for this problem is estimated to be around 1.0 hour.
It is important to address this issue promptly to ensure the proper functioning of your vehicle’s ABS system.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Unveiling The Mystery: Symptoms Of Fault Code P1317 Revealed!
When the engine light is on or the service engine soon warning light is illuminated, it could be a sign of the p1317 fault code.
- The symptoms of the automobile fault code p1317 include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.
Unraveling The Mystery: What Causes Fault Code P1317?
The automobile fault code p1317 can be caused by a faulty ABS speed sensor, an open or shorted ABS speed sensor harness, a poor electrical connection in the ABS speed sensor circuit, or a faulty Engine Control Module (ECM).
- The fault code P1317 can be caused by the following: a faulty ABS speed sensor, an open or shorted ABS speed sensor harness, a poor electrical connection in the ABS speed sensor circuit, and a faulty Engine Control Module (ECM).
Fixing Code P1317: Simple Steps To Get Your Car Running Smoothly!
To fix the p1317 fault code, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.
- To fix the automobile fault code p1317, you need to follow these steps: 1.
- Check the possible causes mentioned above.
- 2.
- Visually inspect the wiring harness and connectors related to the fault code.
- 3.
- Look for any damaged components.
- 4.
- Check for broken, bent, pushed out, or corroded pins in the connectors.
- 5.
- Repairing this fault code is estimated to take approximately 1.0 hour.
Cracking The Code: P1317 – Cost And Complexity Unveiled!
The factors influencing the cost of diagnosing and fixing the automobile fault code p1317 are the estimated repair time of 1.0 hour and the hourly rate charged by auto repair shops, which typically ranges between $75 and $150.
P1317 Fault Code: Uncovering The Mystery Behind Engine Misfire
The P1317 fault code refers to a problem with the Anti-Lock Brake System (ABS) in your vehicle. The ABS uses sensors to detect if the vehicle is on a rough surface that could cause a false misfire detection. When the Engine Control Module (ECM) determines that the surface is rough enough to potentially create a misfire signal, it disables the misfire detection to prevent false Diagnostic Trouble Codes (DTCs).
However, the P1317 code indicates that there is an issue with the ABS rough road signal line. This line is either stuck at ground or has an open circuit. This means that the signal from the ABS system is not being properly transmitted, which can lead to incorrect misfire detection and potentially trigger a false DTC.
It is important to have this issue addressed to ensure the proper functioning of your ABS system and prevent any potential misfire-related problems.
FAQ
If you see the engine light or service engine soon warning light on, the fault code P1317 could be the culprit. This code is often caused by a faulty ABS speed sensor, an open or shorted ABS speed sensor harness, a poor electrical connection in the ABS speed sensor circuit, or a faulty Engine Control Module (ECM). To fix the issue, visually inspect the wiring harness and connectors, checking for any damage or broken, bent, pushed out, or corroded pins. Don’t forget to also address the possible causes mentioned above.
If you’re dealing with the P1317 fault code and your engine light is on, it’s time to take action. The cause could be a faulty ABS speed sensor, an open or shorted ABS speed sensor harness, a poor electrical connection in the ABS speed sensor circuit, or a faulty Engine Control Module (ECM). To fix it, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins. Don’t delay, get to the bottom of this issue and get your engine running smoothly again.
When resolving the P1317 fault code, start by checking for damaged components and connector pins. This can be done by visually inspecting the related wiring harness and connectors. Look for any signs of damage such as broken, bent, pushed out, or corroded connector pins. By doing this, you can identify any issues that may be causing the fault code and take the necessary steps to fix them.
Wrap Up
If your engine light is on and you’re seeing the P1317 fault code, it could be due to a faulty ABS speed sensor, an open or shorted ABS speed sensor harness, a poor electrical connection in the ABS speed sensor circuit, or a faulty Engine Control Module (ECM). To fix this issue, visually inspect the wiring harness and connectors, check for damaged components, and look for any broken, bent, pushed out, or corroded connector pins.
