The automobile fault code P118E indicates a problem with the Exhaust Gas Temperature Sensor. This can cause the Engine Light to turn on.
To fix this issue, you should visually inspect the wiring harness and connectors for any damage. Look for broken, bent, pushed out, or corroded pins in the connectors. The repair time for this issue is estimated to be around 1.0 hour.
It is important to address this problem promptly to prevent further damage to the engine.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Decode The Symptoms: Unveiling The P118E Fault Code Mystery!
If you see the Engine Light ON or the Service Engine Soon Warning Light, it could be due to the p118e fault code.
- The symptoms of the automobile fault code P118E include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.
Unraveling The Mystery: What Causes Fault Code P118E?
The automobile fault code P118E can be caused by a faulty exhaust gas temperature sensor, open or shorted sensor harness, poor electrical connection in the sensor circuit, or a faulty engine control module (ECM).
- The fault code P118E can be caused by: a faulty Exhaust Gas Temperature Sensor, an open or shorted Exhaust Gas Temperature Sensor harness, a poor electrical connection in the Exhaust Gas Temperature Sensor circuit, or a faulty Engine Control Module (ECM).
Fixing Code P118E: Simple Steps To Resolve The Issue
To fix the automobile fault code p118e, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.
- To fix the automobile fault code P118E, start by checking the possible causes mentioned above.
- Then, visually inspect the wiring harness and connectors related to the issue.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
- The estimated repair time for this fix is 1.0 hour.
Cracking The Code: P118E – Cost And Complexity Unveiled!
The factors influencing the cost of diagnosing and fixing the automobile fault code P118E based on the estimated repair time of 1.0 hour include the hourly rate charged by auto repair shops, which typically ranges between $75 and $150.
P118E Fault Code: Understanding The Cause And Solution
The P118E fault code refers to the performance of the exhaust gas temperature sensor 1 while the engine is running.
This sensor is a variable resistor that measures the temperature of the exhaust gas. It is the first sensor on the exhaust system, with subsequent sensors counted from the engine outlet to the end of the exhaust system.
The Engine Control Module (ECM) supplies 5 V to the exhaust gas temperature signal circuit and provides a ground to the low reference circuit.
The information from the exhaust gas temperature sensor is used by the ECM during the exhaust gas particulate filter cleaning process.
If the ECM detects that the difference between the measured exhaust gas temperature and the estimated exhaust gas temperature is greater than a calibrated amount for more than 1 second, it will set the Diagnostic Trouble Code (DTC) P118E. This code indicates a performance issue with the exhaust gas temperature sensor 1 while the engine is running.
FAQ
If you’re seeing the engine light or service engine soon warning light, the fault code P118E could be the culprit. This code is often caused by a faulty exhaust gas temperature sensor, an open or shorted sensor harness, a poor electrical connection in the sensor circuit, or a faulty engine control module (ECM). To fix the issue, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins. Don’t forget to check the possible causes listed above for a more comprehensive solution.
To fix the P118E fault code, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check if there are any broken, bent, pushed out, or corroded pins in the connectors. This can help identify any issues with the Exhaust Gas Temperature Sensor or poor electrical connections. Don’t forget to also check the other possible causes listed above.
When resolving the P118E fault code, start by checking for damaged components and connector pins. This can be done by visually inspecting the related wiring harness and connectors. Look for any signs of damage such as broken, bent, pushed out, or corroded connector pins. By doing this, you can identify any issues that may be causing the fault code and take the necessary steps to fix them.
Wrap Up
If your engine light is on, it could be due to a faulty Exhaust Gas Temperature Sensor or issues with the sensor’s wiring. To fix this, visually inspect the wiring harness and connectors for any damage. Check for broken, bent, pushed out, or corroded pins on the connectors.
