The automobile fault code P10E2 indicates a problem with the Valvetronic Actuator Motor Position Sensor. This can cause the Engine Light to turn on or the Service Engine Soon Warning Light to illuminate.

To fix this issue, you should visually inspect the wiring harness and connectors for any damage. Look for broken, bent, pushed out, or corroded pins on the connectors. The repair time for this fault code is estimated to be around 1.0 hour.

It is important to address this issue promptly to prevent further damage to the vehicle.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

When the engine light is on or the service engine soon warning light is illuminated, it could be a sign of the p10e2 fault code.

  • The symptoms of the automobile fault code P10E2 include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.

The automobile fault code p10e2 can be caused by a faulty Valvetronic Actuator Motor Position Sensor, an open or shorted harness, or a poor electrical connection in the sensor circuit.

  • The fault code P10E2 can be caused by: a faulty Valvetronic Actuator Motor Position Sensor, an open or shorted harness for the Valvetronic Actuator Motor Position Sensor, or a poor electrical connection in the Valvetronic Actuator Motor Position Sensor circuit.

To resolve the p10e2 fault code, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.

  • To fix the automobile fault code P10E2, start by checking the possible causes mentioned above.
  • Then, visually inspect the wiring harness and connectors related to the issue.
  • Look for any damaged components and check if there are any broken, bent, pushed out, or corroded pins in the connectors.
  • This fix is estimated to take approximately 1.0 hour.

The factors influencing the cost of diagnosing and fixing the automobile fault code P10E2 are the estimated repair time of 1.0 hour and the typical hourly rate charged by auto repair shops, which ranges from $75 to $150.

The P10E2 fault code is related to the Valvetronic Actuator Motor Position Sensor in the Engine Control Module (ECM). This sensor is responsible for monitoring the position of the Valvetronic Actuator Motor. When the sensor does not meet the factory specifications, the ECM sets the P10E2 Diagnostic Trouble Code (DTC).

The P10E2 code specifically indicates an issue with the Valvetronic Sensors Supply Voltage Circuit Electrical.

This means that there is an electrical problem in the circuit that supplies voltage to the Valvetronic sensors. It is important to address this issue promptly to ensure proper functioning of the Valvetronic system and avoid potential engine performance problems.

What are the possible causes for the automobile fault code P10E2?

If you’re seeing the engine light on or the service engine soon warning light, the fault code P10E2 could be the culprit. This code is often caused by a faulty Valvetronic Actuator Motor Position Sensor or issues with the sensor’s wiring harness. To fix the problem, start by visually inspecting the wiring harness and connectors. Look for any signs of damage or corrosion. Additionally, check for broken, bent, pushed out, or corroded pins in the connectors. By addressing these possible causes, you can get your automobile back on track.

How can I visually inspect the wiring harness and connectors to fix the P10E2 fault code?

To fix the P10E2 fault code, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check if there are any broken, bent, pushed out, or corroded pins in the connectors. This can help identify if the issue lies with a faulty Valvetronic Actuator Motor Position Sensor or if there is an open or shorted circuit. Take note of any findings to assist in the troubleshooting process.

What should I look for when checking for damaged components or corroded connector pins to resolve the P10E2 fault code?

When resolving the P10E2 fault code, start by checking for damaged components or corroded connector pins. This can be done by visually inspecting the related wiring harness and connectors. Look for any broken, bent, pushed out, or corroded pins on the connectors. By doing so, you can identify any issues with the Valvetronic Actuator Motor Position Sensor and its circuit connections, which may be causing the engine light to turn on.

p10e2 error fault code explained

If you’re seeing the Engine Light ON or the Service Engine Soon Warning Light, the p10e2 fault code might be the culprit. This is usually caused by a faulty Valvetronic Actuator Motor Position Sensor or issues with the sensor’s wiring harness and electrical connection.

To fix it, visually inspect the wiring harness and connectors, checking for any damage or corrosion.

Look out for broken, bent, pushed out, or corroded connector pins.

Scroll to Top