The automobile fault code P0BD7 indicates a problem with the Inverter With Converter Assembly. The most common symptom is the Engine Light being ON or the Service Engine Soon Warning Light. The cause of this fault code can be a faulty Inverter With Converter Assembly, an open or shorted harness, a poor electrical connection in the circuit, or a faulty HV Control ECU.

To fix this issue, you should visually inspect the wiring harness and connectors for any damage. Look for broken, bent, pushed out, or corroded pins in the connectors. The repair time for this issue is estimated to be around 1.0.

It is important to address this problem promptly to prevent further damage to the vehicle.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

When the engine light is on or the service engine soon warning light is illuminated, it could be a sign of the p0bd7 fault code.

  • The symptoms of the automobile fault code p0bd7 include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.

The automobile fault code p0bd7 can be caused by a faulty inverter with converter assembly, open or shorted harness, poor electrical connection in the circuit, or a faulty HV control ECU.

  • The fault code p0bd7 can be caused by: a faulty Inverter With Converter Assembly, an open or shorted Inverter With Converter Assembly harness, a poor electrical connection in the Inverter With Converter Assembly circuit, or a faulty HV Control ECU.

To fix the automobile fault code p0bd7, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.

  • To fix the automobile fault code p0bd7, first, check the possible causes mentioned above.
  • Then, visually inspect the wiring harness and connectors related to the issue.
  • Look for any damaged components and check for broken, bent, pushed out, or corroded pins in the connectors.
  • The estimated repair time for this fix is 1.0 hour.

The factors influencing the cost of diagnosing and fixing the automobile fault code p0bd7 include the estimated repair time of 1.0 hour and the typical hourly rate charged by auto repair shops, which ranges between $75 and $150.

The P0BD7 fault code refers to a problem with the Drive Motor Inverter Temperature Sensor ‘D’ Circuit RangePerformance.

This sensor is located in the inverter and is used by the HV control ECU to monitor the temperature of the motor inverter.

The same cooling system that cools the MG1 and MG2 is also used to cool the inverter, and the sensor’s characteristics are similar to the boost converter temperature sensor.

The HV control ECU uses the signals from the motor inverter temperature sensor to limit the load and ensure the effectiveness of the inverter cooling system. It also detects any issues with the wiring or the sensor itself.

This code indicates that there is a problem with the circuit range or performance of the temperature sensor. It is important to address this issue to prevent overheating of the inverter and potential damage to the vehicle.

What are the possible causes for the automobile fault code p0bd7?

If you see the engine light or service engine soon warning light on, the fault code P0BD7 could be the culprit. This code is often caused by a faulty inverter with converter assembly, an open or shorted harness, a poor electrical connection in the inverter with converter assembly circuit, or a faulty HV control ECU. To fix the issue, visually inspect the wiring harness and connectors, checking for any damage or broken, bent, pushed out, or corroded pins. Don’t forget to also check the possible causes listed above.

How can I visually inspect the wiring harness and connectors to fix the issue?

To fix the issue of the Engine Light being ON or the Service Engine Soon Warning Light, start by checking the possible causes mentioned above. Then, visually inspect the wiring harness and connectors associated with the Inverter With Converter Assembly. Look for any damaged components and check if there are any broken, bent, pushed out, or corroded pins in the connectors. This thorough inspection will help identify and resolve any issues with the wiring harness and connectors.

What should I look for when checking for damaged components or corroded connector pins?

When troubleshooting an engine light or service engine soon warning light, it’s important to check for damaged components and corroded connector pins. To fix the issue, visually inspect the related wiring harness and connectors. Look for any broken, bent, pushed out, or corroded pins on the connectors. This can help identify any faults in the inverter with converter assembly or the HV control ECU. Don’t forget to also check the other possible causes listed above.

p0bd7 error fault code explained

If you’re seeing the Engine Light ON or the Service Engine Soon Warning Light, the p0bd7 fault code might be the culprit. This code is usually caused by a faulty Inverter With Converter Assembly or issues with the wiring harness and connectors. To fix it, visually inspect the wiring and connectors for any damage, and check for broken or corroded pins.

Scroll to Top