The automobile fault code P0BC5 indicates a problem with the HybridEV Battery Assembly. The most common symptom is the Engine Light being ON or the Service Engine Soon Warning Light. The cause of this fault code can be a faulty HybridEV Battery Assembly, an open or shorted harness, a poor electrical connection in the circuit, or a faulty HybridEV Battery Interface Control Module.

To fix this issue, you should visually inspect the wiring harness and connectors for any damage. Look for broken, bent, pushed out, or corroded pins in the connectors. The repair time for this issue is estimated to be around 1.0.

It is important to address this problem promptly to avoid further complications.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

When the p0bc5 fault code appears, the Engine Light will illuminate, indicating a potential issue with your vehicle.

  • The symptoms of the automobile fault code p0bc5 include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.

The automobile fault code p0bc5 can be caused by a faulty HybridEV Battery Assembly, an open or shorted HybridEV Battery Assembly harness, a poor electrical connection in the HybridEV Battery Assembly circuit, or a faulty HybridEV Battery Interface Control Module.

  • The fault code p0bc5 can be caused by a faulty Hybrid/EV Battery Assembly, an open or shorted Hybrid/EV Battery Assembly harness, a poor electrical connection in the Hybrid/EV Battery Assembly circuit, or a faulty Hybrid/EV Battery Interface Control Module.

To fix the automobile fault code p0bc5, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.

  • To fix the automobile fault code p0bc5, start by checking the possible causes mentioned above.
  • Then, visually inspect the wiring harness and connectors for any damage.
  • Look for broken, bent, pushed out, or corroded pins on the connectors.
  • This fix should take approximately 1.0 hour.

The factors influencing the cost of diagnosing and fixing the automobile fault code p0bc5 are the estimated repair time of 1.0 hour and the typical hourly rate charged by auto repair shops, which ranges from $75 to $150.

The P0BC5 fault code refers to a problem with the HybridEV Battery Temperature Sensor 5 Circuit. This sensor is responsible for monitoring the temperature of the battery in hybrid or electric vehicles.

It is located within the battery sections and there are two temperature sensors in each section.

The sensor works by measuring the resistance of the battery cell group, which changes with temperature. As the temperature decreases, the sensor resistance increases, and as the temperature increases, the sensor resistance decreases.

The HybridEV Interface Control Module supplies 5V to the signal circuit and acts as a ground for the low reference circuit. It communicates the temperature sensor values to the HybridEV Powertrain Control Module via serial data.

When the hybrid battery temperature sensor reads a temperature below -69°C (-92°F), the P0BC5 fault code is triggered. This code indicates a high voltage issue with the HybridEV Battery Temperature Sensor 5 Circuit.

It is important to address this issue promptly to ensure proper operation of the battery cooling system.

What are the possible causes for the automobile fault code p0bc5?

If you see the engine light on or the service engine soon warning light, the fault code P0BC5 could be the culprit. This code is often caused by a faulty Hybrid/EV Battery Assembly, an open or shorted harness, a poor electrical connection in the Hybrid/EV Battery Assembly circuit, or a faulty Hybrid/EV Battery Interface Control Module. To fix this issue, visually inspect the wiring harness and connectors, checking for any damage or broken, bent, pushed out, or corroded pins in the connectors. Don’t forget to consider the possible causes mentioned above.

How can I visually inspect the wiring harness and connectors to fix the fault code p0bc5?

If you’re dealing with the fault code p0bc5 and your engine light is on, it’s time to take a closer look at the wiring harness and connectors. The possible causes could be a faulty Hybrid/EV Battery Assembly, an open or shorted harness, a poor electrical connection in the circuit, or a faulty Hybrid/EV Battery Interface Control Module. To fix the issue, visually inspect the wiring harness and connectors for any signs of damage. Check for broken, bent, pushed out, or corroded pins on the connectors. Don’t forget to consider the possible causes mentioned earlier.

What should I look for when checking the connector’s pins to resolve the fault code p0bc5?

When resolving the fault code p0bc5, start by checking the connector’s pins. Visually inspect the wiring harness and connectors for any damage. Look out for broken, bent, pushed out, or corroded pins. These issues can cause a poor electrical connection and trigger the engine light to come on. By addressing these potential causes, such as a faulty Hybrid/EV Battery Assembly or a problem with the Hybrid/EV Battery Interface Control Module, you can effectively resolve the fault code. Act now to prevent further complications.

p0bc5 error fault code explained

If you’re seeing the Engine Light ON or the Service Engine Soon Warning Light, the p0bc5 fault code might be the culprit. This code is usually caused by a faulty HybridEV Battery Assembly or issues with the wiring harness and connectors. To fix it, visually inspect the wiring and connectors for any damage, and check for broken or corroded pins.

Scroll to Top