The automobile fault code P0B6A indicates a problem with the hybridelectric vehicle battery pack or the battery interface control module. The most common symptom is the engine light being illuminated or the service engine soon warning light. To fix this issue, you should visually inspect the wiring harness and connectors for any damage.

Look out for broken, bent, pushed out, or corroded connector pins. The repair time for this fault code is estimated to be around 1.0.

It is important to address this issue promptly to ensure the proper functioning of your vehicle.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

When the engine light is on or the service engine soon warning light is illuminated, it could be a sign of the p0b6a fault code.

  • The symptoms of the automobile fault code p0b6a include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.

The automobile fault code p0b6a can be caused by a faulty HybridElectric Vehicle Battery Pack or a faulty HybridElectric Vehicle Battery Interface Control Module.

  • The fault code p0b6a can be caused by a faulty Hybrid/Electric Vehicle Battery Pack or a faulty Hybrid/Electric Vehicle Battery Interface Control Module.

To fix the automobile fault code p0b6a, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.

  • To fix the automobile fault code p0b6a, start by checking the possible causes mentioned above.
  • Then, visually inspect the wiring harness and connectors related to the issue.
  • Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
  • This fix is estimated to take approximately 1.0 hour.

The factors influencing the cost of diagnosing and fixing the automobile fault code p0b6a are the estimated repair time and the hourly rate charged by auto repair shops. The estimated repair time for this fault code is 1.0 hour. Auto repair shops typically charge between $75 and $150 per hour for their services.

These factors will determine the overall cost of diagnosing and fixing the p0b6a fault code.

The P0B6A fault code refers to a low voltage condition in the HybridElectric Vehicle battery circuit. The battery pack consists of 288 cells, grouped in parallel sets of three.

There are a total of 96 cell groups connected in series, with each group rated at 3.7V. The nominal system voltage is 355V DC. The battery cells are divided into three sections. Section one has 90 cells30 cell groups, located adjacent to the cowl.

Section two is behind section one and contains 72 cells24 cell groups. Section three, the transverse section, has the remaining 126 cells42 cell groups. The battery energy control module monitors the voltage of the cell groups through hybridEV battery interface control modules.

Voltage sense circuits are attached to each cell group, and the readings are transmitted to the battery energy control module. When a fault condition is detected, the battery energy control module communicates with the hybridEV powertrain control module 2 through serial data. The powertrain control module is responsible for diagnostic trouble code information. In summary, the P0B6A fault code indicates a low voltage issue in the HybridElectric Vehicle battery circuit, which is monitored and communicated by the battery energy control module and the powertrain control module.

What are the possible causes for the automobile fault code P0B6A?

If you see the engine light or service engine soon warning light on, the fault code P0B6A could be the culprit. This code is often caused by a faulty hybrid/electric vehicle battery pack or a faulty hybrid/electric vehicle battery interface control module. To fix the issue, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins. Don’t forget to check the possible causes listed above for further troubleshooting.

How can I visually inspect the wiring harness and connectors to fix the P0B6A fault code?

To fix the P0B6A fault code, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check if there are any broken, bent, pushed out, or corroded pins in the connectors. This can help identify any issues with the Hybrid/Electric Vehicle Battery Pack or the Battery Interface Control Module, which could be causing the Engine Light to turn on. Don’t forget to check the “Possible Causes” listed above for further troubleshooting.

What should I look for when checking for damaged components and corroded connector pins to resolve the P0B6A fault code?

When resolving the P0B6A fault code, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins. This can help identify any issues with the Hybrid/Electric Vehicle Battery Pack or the Hybrid/Electric Vehicle Battery Interface Control Module, which are common causes of this fault code. Don’t forget to check the “Possible Causes” listed above for further troubleshooting.

p0b6a error fault code explained

If you’re seeing the Engine Light ON or the Service Engine Soon Warning Light, the p0b6a fault code might be the culprit. This code is usually caused by a faulty HybridElectric Vehicle Battery Pack or a faulty HybridElectric Vehicle Battery Interface Control Module. To fix it, visually inspect the wiring harness and connectors, check for damaged components, and look for any broken, bent, pushed out, or corroded connector pins.

Scroll to Top