The automobile fault code P0B61 indicates a problem with the hybridelectric vehicle battery pack or the battery interface control module. The most common symptom is the engine light being illuminated or the service engine soon warning light. To fix this issue, you should visually inspect the wiring harness and connectors for any damage.

Look out for broken, bent, pushed out, or corroded connector pins. The repair time for this fault code is estimated to be around 1.0. It is important to address this issue promptly to ensure the proper functioning of your vehicle.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

When the engine light is on or the service engine soon warning light is illuminated, it could be a sign of the p0b61 fault code.

  • The symptoms of the automobile fault code p0b61 include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.

The automobile fault code p0b61 can be caused by a faulty HybridElectric Vehicle Battery Pack or a faulty HybridElectric Vehicle Battery Interface Control Module.

  • The fault code p0b61 can be caused by a faulty Hybrid/Electric Vehicle Battery Pack or a faulty Hybrid/Electric Vehicle Battery Interface Control Module.

To fix the automobile fault code p0b61, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.

  • To fix the automobile fault code p0b61, start by checking the possible causes mentioned above.
  • Then, visually inspect the wiring harness and connectors for any damage.
  • Look for broken, bent, pushed out, or corroded pins on the connectors.
  • This fix should take approximately 1.0 hour.

The factors influencing the cost of diagnosing and fixing the automobile fault code p0b61 are the estimated repair time of 1.0 hour and the typical hourly rate charged by auto repair shops, which ranges from $75 to $150.

The P0B61 fault code refers to a high voltage issue in the HybridElectric Vehicle battery circuit 8.

The battery pack consists of 288 cells, grouped in parallel sets of three. There are a total of 96 cell groups connected in series, with each group rated at 3.7V. The nominal system voltage is 355V DC.

The battery cells are divided into three sections: section one with 90 cells, section two with 72 cells, and section three with 126 cells.

Each section contains a specific range of batteries. The battery energy control module monitors the voltage of the cell groups through hybridEV battery interface control modules.

These modules encode the voltage readings and transmit them to the battery energy control module. If a fault condition is detected, the battery energy control module communicates this information to the hybridEV powertrain control module 2, which serves as the diagnostic trouble code host controller.

In the case of the P0B61 code, it indicates a high voltage problem in circuit 8 of the HybridElectric Vehicle battery.

What are the possible causes of the automobile fault code p0b61?

If you see the engine light or service engine soon warning light on, the fault code P0B61 could be the culprit. This code is often caused by a faulty hybrid/electric vehicle battery pack or a faulty hybrid/electric vehicle battery interface control module. To fix the issue, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins. Don’t forget to check the possible causes listed above for a more comprehensive solution.

How can I visually inspect the wiring harness and connectors to fix the fault code p0b61?

If you’re dealing with the fault code p0b61 and your engine light is on, it’s time to visually inspect the wiring harness and connectors. This could be caused by a faulty hybrid/electric vehicle battery pack or a faulty hybrid/electric vehicle battery interface control module. To fix it, check the possible causes mentioned earlier and give the wiring harness and connectors a thorough visual inspection. Look out for any damaged components and check for broken, bent, pushed out, or corroded connector pins.

What should I look for when checking for damaged components and connector’s pins to resolve the fault code p0b61?

When resolving the fault code p0b61, start by checking for damaged components and connector’s pins. This can be done by visually inspecting the related wiring harness and connectors. Look for any signs of damage such as broken, bent, pushed out, or corroded pins. By identifying and addressing these issues, you can effectively resolve the problem and get your engine light or service engine soon warning light turned off. Don’t forget to also consider the possible causes mentioned above, such as a faulty hybrid/electric vehicle battery pack or a faulty hybrid/electric vehicle battery interface control module.

p0b61 error fault code explained

If you’re seeing the Engine Light ON or the Service Engine Soon Warning Light, the p0b61 fault code might be the culprit.

This code is usually caused by a faulty HybridElectric Vehicle Battery Pack or a faulty HybridElectric Vehicle Battery Interface Control Module. To fix it, visually inspect the wiring harness and connectors, check for damaged components, and look for any broken, bent, pushed out, or corroded connector pins.

Scroll to Top