[SOLVED] P0Afa Code: Hybrid Battery Voltage Low – How To Fix It!

The automobile fault code P0AFA indicates a problem with the hybrid battery pack in your vehicle.

The most common symptom is the engine light being illuminated or the service engine soon warning light appearing on your dashboard.

The cause of this fault code can be attributed to various issues such as an open 36 volt battery cable, a blown hybrid battery pack fuse, an open hybrid battery pack contactor, or a faulty hybrid battery pack ground cable or connection. To fix this issue, you should start by visually inspecting the wiring harness and connectors related to the hybrid battery pack.

Look for any signs of damage or corrosion. Additionally, check for any broken, bent, pushed out, or corroded pins in the connectors.

It is important to address this fault code promptly as it can affect the performance and efficiency of your vehicle. The repair time for this issue is estimated to be around 1.0 hour. To interpret the fault code, refer to the “Possible Causes” listed above and follow the recommended steps for inspection and repair.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

When the engine light is on or the service engine soon warning light is illuminated, it could be a sign of the p0afa fault code.

  • The symptoms of the automobile fault code p0afa include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.

The automobile fault code p0afa can be caused by issues such as an open 36 volt battery cable, open Hybrid Battery Pack fuse, open Hybrid Battery Pack contactor, or a faulty Hybrid Battery Pack ground cable or connection.

  • The fault code p0afa can be caused by the following issues: 36 volt battery cable open, Hybrid Battery Pack fuse open, Hybrid Battery Pack contactor open, and Hybrid Battery Pack ground cable or connection.

To fix the automobile fault code p0afa, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.

  • To fix the automobile fault code p0afa, start by checking the possible causes mentioned above.
  • Then, visually inspect the wiring harness and connectors related to the issue.
  • Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
  • This fix should take approximately 1.0 hour.

The automobile fault code P0AFA has an estimated repair time of 1.0 hour.

Auto repair shops typically charge between $75 and $150 per hour for this type of repair.

The P0AFA fault code indicates a low voltage in the hybrid battery system. The Engine Control Module (ECM) monitors the correlation between the generator battery disconnect control module battery voltage and the Starter Generator Control Module (SGCM) output voltage. It does this to detect a 36 volt cable open or fuserelay failure.

The ECM also monitors for an over voltage condition to protect the MOSFET (load dump).

If either of these conditions is detected, the P0AFA code will be set. This code serves as a warning that the hybrid battery system voltage is too low and needs attention.

What are the possible causes for the automobile fault code p0afa?

If you see the engine light or service engine soon warning light on, the fault code P0AFA could be the culprit. This code can be caused by a few things, including an open 36 volt battery cable, an open hybrid battery pack fuse, an open hybrid battery pack contactor, or an issue with the hybrid battery pack ground cable or connection. To fix this, start by checking the possible causes mentioned above. Take a close look at the wiring harness and connectors, checking for any damage or broken, bent, pushed out, or corroded pins on the connectors.

How can I visually inspect the wiring harness and connectors to fix the p0afa fault code?

If you’re dealing with the p0afa fault code and your engine light is on, it’s time to take a closer look at the wiring harness and connectors. The possible causes include issues like an open 36 volt battery cable, a blown Hybrid Battery Pack fuse, an open Hybrid Battery Pack contactor, or a problem with the Hybrid Battery Pack ground cable or connection. To fix this, visually inspect the wiring harness and connectors for any signs of damage. Check for broken, bent, pushed out, or corroded pins on the connectors. Don’t forget to check the “Possible Causes” mentioned earlier.

What should I look for when checking for damaged components or broken, bent, pushed out, or corroded connector’s pins to resolve the p0afa fault code?

When resolving the p0afa fault code, it is important to visually inspect the wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins. These issues can often be the cause of the problem. By thoroughly checking for these issues, you can identify and resolve the underlying cause of the fault code.

p0afa error fault code explained

If your engine light is on or you see the service engine soon warning light, it could be due to a p0afa fault code. This is usually caused by issues with the 36 volt battery cable, hybrid battery pack fuse, hybrid battery pack contactor, or hybrid battery pack ground cableconnection. To fix it, visually inspect the wiring harness and connectors, check for damaged components, and look for any broken, bent, pushed out, or corroded connector pins.

Scroll to Top