The automobile fault code P0ACD indicates a problem with the HybridEV Battery Assembly. The most common symptom is the Engine Light being ON or the Service Engine Soon Warning Light.

The cause of this fault code can be a faulty HybridEV Battery Assembly, an open or shorted harness, a poor electrical connection in the circuit, or a faulty HybridEV Battery Interface Control Module. To fix this issue, you should visually inspect the wiring harness and connectors for any damage.

Look for broken, bent, pushed out, or corroded pins in the connectors. The repair time for this issue is estimated to be around 1.0 hour. It is important to address this problem promptly to prevent further damage to the vehicle’s hybrid or electric system.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

When the engine light is on or the service engine soon warning light is illuminated, it could be a sign of the p0acd fault code.

  • The symptoms of the automobile fault code p0acd include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.

The automobile fault code p0acd can be caused by a faulty HybridEV Battery Assembly, an open or shorted HybridEV Battery Assembly harness, a poor electrical connection in the HybridEV Battery Assembly circuit, or a faulty HybridEV Battery Interface Control Module.

  • The fault code p0acd can be caused by a faulty Hybrid/EV Battery Assembly, an open or shorted Hybrid/EV Battery Assembly harness, a poor electrical connection in the Hybrid/EV Battery Assembly circuit, or a faulty Hybrid/EV Battery Interface Control Module.

To fix the automobile fault code p0acd, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.

  • To fix the automobile fault code p0acd, start by checking the possible causes mentioned above.
  • Then, visually inspect the wiring harness and connectors related to the issue.
  • Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
  • This fix is estimated to take approximately 1.0 hour.

The factors influencing the cost of diagnosing and fixing the automobile fault code p0acd are the estimated repair time and the hourly rate charged by auto repair shops.

The estimated repair time for this fault code is 1.0 hour. Auto repair shops typically charge between $75 and $150 per hour for their services.

These factors will determine the overall cost of diagnosing and fixing the p0acd fault code.

The P0ACD fault code refers to a problem with the HybridEV Battery Temperature Sensor 3 Circuit.

This sensor is responsible for monitoring the temperature of the battery in hybrid or electric vehicles. It is located within the battery sections and there are two temperature sensors in each section. The sensor works by measuring the resistance of the battery cell group, which changes with temperature. As the temperature decreases, the sensor resistance increases, and as the temperature increases, the sensor resistance decreases.

The HybridEV interface control module supplies 5V to the signal circuit and acts as a ground for the low reference circuit. The HybridEV Powertrain Control Module uses the temperature sensor values to determine the battery module temperature and control the battery cooling system. If the hybrid battery temperature sensor reads a temperature below -69°C (-92°F), the P0ACD fault code will be triggered. This indicates a high voltage issue in the HybridEV Battery Temperature Sensor 3 Circuit.

What are the possible causes for the automobile fault code p0acd?

If you see the engine light on or the service engine soon warning light, the fault code P0ACD could be the culprit. This code is often caused by a faulty hybrid/EV battery assembly, an open or shorted harness, a poor electrical connection in the hybrid/EV battery assembly circuit, or a faulty hybrid/EV battery interface control module. To fix this issue, visually inspect the wiring harness and connectors, checking for any damage or broken, bent, pushed out, or corroded pins in the connectors. Don’t forget to also check the possible causes listed above.

How can I visually inspect the wiring harness and connectors to fix the fault code p0acd?

If you’re dealing with the fault code p0acd and your engine light is on, it’s time to visually inspect the wiring harness and connectors. This could be caused by a faulty Hybrid/EV Battery Assembly, an open or shorted harness, a poor electrical connection in the circuit, or a faulty Hybrid/EV Battery Interface Control Module. To fix it, check the possible causes mentioned earlier and visually inspect the wiring harness and connectors. Look out for damaged components and check for broken, bent, pushed out, or corroded connector pins.

What should I look for when checking for damaged components and connector’s pins to resolve the fault code p0acd?

If you’re dealing with the fault code p0acd and your engine light is on, it’s time to roll up your sleeves and get to work. The culprit could be a faulty Hybrid/EV Battery Assembly or a poor electrical connection in the Hybrid/EV Battery Assembly circuit. To fix this, start by visually inspecting the wiring harness and connectors. Look out for any damaged components and pay close attention to the connector’s pins – they might be broken, bent, pushed out, or corroded. Don’t forget to check the “Possible Causes” listed above for a comprehensive solution.

p0acd error fault code explained

If you see the Engine Light ON or the Service Engine Soon Warning Light, the p0acd fault code might be the culprit. This code is usually caused by a faulty HybridEV Battery Assembly, an open or shorted harness, a poor electrical connection in the HybridEV Battery Assembly circuit, or a faulty HybridEV Battery Interface Control Module.

To fix it, visually inspect the wiring harness and connectors, check for damaged components, and look for any broken, bent, pushed out, or corroded connector pins.

Scroll to Top