The automobile fault code U1204 indicates a problem with the Powertrain Control Module (PCM), Battery Condition Monitor (BCM) Module, or Motor Control Module (MCM). The most common symptom is the Engine Light ON or Service Engine Soon Warning Light.
The cause of this fault code could be a faulty PCM, open or shorted PCM harness, poor electrical connection, or a faulty BCM or MCM. The repair importance is high as it affects the engine’s performance and fuel efficiency. The repair difficulty is moderate, and the repair time is estimated at 1.0 hour.
To fix the issue, one should visually inspect the related wiring harness and connectors and check for damaged components and connector pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
Decoding U1204: Common Symptoms Of This Fault Code
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the u1204 fault code. Here are the symptoms to look out for:
- The automobile fault code U1204 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light ON.
Decoding U1204: Common Causes Of The Fault Code
The automobile fault code u1204 can be caused by a range of issues, including a faulty PCM, BCM, MCM, or poor electrical connections.
- The automobile fault code u1204 can be caused by a faulty Powertrain Control Module (PCM).
- It can also be caused by an open or shorted Powertrain Control Module harness.
- Poor electrical connection in the Powertrain Control Module circuit can also trigger this fault code.
- Another cause of u1204 is a faulty Battery Condition Monitor (BCM) Module.
- Lastly, a faulty Motor Control Module (MCM) can also cause this fault code to appear.
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Fix U1204 Code: Simple Steps To Get Your Car Running
To fix the u1204 automobile fault code, check the possible causes and inspect the related wiring harness, connectors, and components for damage.
- To fix the automobile fault code u1204, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U1204 Diagnosis Cost & Complexity
The automobile fault code U1204 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour.
Therefore, the total cost of fixing the U1204 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to diagnose and fix the issue.
Decoding U1204: Understanding The Cause Of Communication Failure
The u1204 fault code is related to the Integrated Motor Assist (IMA) – Controller Area Network (CAN) system in automobiles. This system uses two signal lines, IMACANH and IMACANL, to receive and transmit multiple signals simultaneously tofrom multiple control modules.
When the information is not sent from the Powertrain Control Module (PCM) through the IMA-CAN or when the information sent from the PCM is abnormal, the Battery Condition Monitor (BCM) module detects a malfunction and a DTC is stored.
FAQ
If your engine light is on and you’re seeing the u1204 fault code, it could be due to a faulty Powertrain Control Module (PCM), an open or shorted PCM harness, poor electrical connection in the PCM circuit, a faulty Battery Condition Monitor (BCM) Module, or a faulty Motor Control Module (MCM). To fix the issue, check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for any damaged components or broken, bent, pushed out, or corroded connector pins.
If you’re experiencing an illuminated Engine Light or Service Engine Soon Warning Light due to the u1204 fault code, there are a few possible causes to consider. These include a faulty Powertrain Control Module (PCM), an open or shorted PCM harness, poor electrical connection in the PCM circuit, a faulty Battery Condition Monitor (BCM) Module, or a faulty Motor Control Module (MCM). To fix the issue, visually inspect the related wiring harness and connectors, checking for damaged components and broken, bent, pushed out, or corroded connector pins.
While a faulty Powertrain Control Module (PCM) is one of the possible causes of the u1204 automobile fault code, it is not the only one. Other causes include a faulty Battery Condition Monitor (BCM) Module, Motor Control Module (MCM), or an open or shorted PCM harness. To fix the issue, one should visually inspect the wiring harness and connectors, and check for damaged components or corroded pins.
Wrap Up
If your engine light is on, it could be due to a faulty Powertrain Control Module (PCM), Powertrain Control Module harness, or a faulty Battery Condition Monitor (BCM) Module.
Check for damaged components and inspect the wiring harness and connectors for any issues.
