If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Throttle Actuator Control (TAC) module. The automobile fault code U0107 indicates that there is an issue with the TAC module or its related wiring harness and connectors.
The cause could be an open or shorted harness, poor electrical connection, or damaged components. It is important to visually inspect the wiring harness and connectors for any damage or corrosion. The repair time for this issue is estimated to be around 1.0.
To interpret the fault code, you can use an OBD-II scanner or take your vehicle to a mechanic.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
Unresponsive Transmission? U0107 Symptoms Explained
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of u0107 fault code. Here are the symptoms to look out for:
- The automobile fault code u0107 has the following symptoms: Engine Light ON, Service Engine Soon Warning Light, issues with the transmission shifting, problems with the speedometer, issues with the cruise control, and the vehicle may not start.
U0107: What Triggers This Fault Code?
The u0107 automobile fault code can be caused by a faulty TAC module, open or shorted TAC module harness, or poor electrical connection.
- The automobile fault code u0107 can be caused by a faulty Throttle Actuator Control (TAC) module.
- It can also be caused by an open or shorted Throttle Actuator Control (TAC) module harness.
- Another cause of this fault code is a poor electrical connection in the Throttle Actuator Control (TAC) module circuit, which can be due to loose or broken wires.
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Fix U0107 Code: Simple Steps To Get Your Car Running
Below are some possible fixes for the automobile fault code u0107, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code u0107, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U0107 Repair Cost & Complexity
The automobile fault code U0107 can be diagnosed and fixed within an estimated repair time of 1.0 hour.
The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour. Therefore, the total cost of fixing the U0107 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.
Unresponsive Control Module: U0107 Explained
The U0107 fault code is related to the Controller Area Network (CAN) in a vehicle. CAN is a bus standard that connects automotive devices without a host computer. CAN bus uses two wires for communication, CAN high and CAN low.
The U0107 code sets when the Throttle Actuator Control Module fails to send a periodic message. This code indicates that there is a communication problem between the Throttle Actuator Control Module and the CAN bus. The Throttle Actuator Control Module is responsible for controlling the throttle opening angle based on the driver’s input.
FAQ
If your engine light is on and you’re seeing the u0107 fault code, it could be due to a faulty Throttle Actuator Control (TAC) module, an open or shorted TAC module harness, or a poor electrical connection in the TAC module circuit. To fix the issue, visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector pins.
If you’re experiencing an Engine Light ON (or Service Engine Soon Warning Light) due to the u0107 fault code, it may be caused by a faulty Throttle Actuator Control (TAC) module, an open or shorted TAC module harness, or a poor electrical connection. To fix it, visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re troubleshooting the u0107 automobile fault code, start by checking for an illuminated Engine Light or Service Engine Soon Warning Light. The cause of this issue could be a faulty Throttle Actuator Control (TAC) module, an open or shorted TAC module harness, or a poor electrical connection in the TAC module circuit. To fix the problem, visually inspect the related wiring harness and connectors, checking for damaged components and broken, bent, pushed out, or corroded connector pins.
Wrap Up
If your engine light is on and the code is u0107, it may be due to a faulty Throttle Actuator Control (TAC) module, an open or shorted TAC module harness, or a poor electrical connection.
To fix it, visually inspect the wiring harness and connectors for damage and check for broken, bent, pushed out, or corroded connector pins.
