The P2535 automobile fault code refers to a problem with the ignition switch or the body control module. The most common symptom is the engine light turning on.
The cause could be a faulty ignition switch, an open or shorted harness, or a poor electrical connection. The repair is not too difficult, and it involves visually inspecting the wiring harness and connectors for any damage or corrosion.
The fault code can be interpreted using an OBD-II scanner.
Repair Importance Level | 10.0 (Out of 10) |
Estimated Repair Time | Approximately 1.0 hour |
Repair Difficulty Level | 10.0 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
P2535: Warning Signs Of A Faulty Fuel Pump Control Circuit
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be a sign of p2535 fault code. Here are the symptoms to look out for:
- The P2535 fault code in an automobile can cause the following symptoms: Engine Light ON, Service Engine Soon Warning Light, issues with the vehicle’s transmission, problems with the vehicle’s speedometer, issues with the vehicle’s cruise control, and issues with the vehicle’s stability control system.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
P2535: Unraveling The Culprits Behind The Fault Code
The automobile fault code p2535 can be caused by a faulty ignition switch, open or shorted harness, poor electrical connection, or a faulty BCM.
- The automobile fault code P2535 can be caused by a faulty ignition on/start switch.
- It can also be caused by an open or shorted ignition on/start switch harness.
- Another possible cause is a poor electrical connection in the ignition on/start switch circuit.
- Lastly, a faulty body control module (BCM) can also trigger this fault code.
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Fix Code P2535: Simple Steps To Get Your Car Running
To fix the automobile fault code p2535, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2535, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2535: Affordable Fix For Complex Automobile Fault Code
The automobile fault code P2535 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops.
Therefore, the total cost of fixing the P2535 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.
P2535: Your Car’s Fuel Pump Control Circuit – Explained
The P2535 code is related to the ignition system of a vehicle.
It indicates that the Body Control Module (BCM) is detecting high voltage on the ignition circuit. This occurs when the ignition is turned off, and the BCM is still receiving a voltage of 6 volts or more. This fault code can cause issues with starting the vehicle and should be addressed promptly.
FAQ
If you see the engine light on or service engine soon warning light, it could be due to the P2535 fault code. This code is caused by a faulty ignition on/start switch, an open or shorted ignition on/start switch harness, a poor electrical connection in the ignition on/start switch circuit, or a faulty body control module (BCM). To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light due to a P2535 fault code, there are a few possible causes to consider. These include a faulty Ignition On/Start Switch, an open or shorted Ignition On/Start Switch harness, a poor electrical connection in the Ignition On/Start Switch circuit, or a faulty Body Control Module (BCM). To fix the issue, start by visually inspecting the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
Yes, a faulty Body Control Module (BCM) can cause the P2535 fault code, which is indicated by the Engine Light ON or Service Engine Soon Warning Light. Other possible causes include a faulty Ignition On/Start Switch, an open or shorted Ignition On/Start Switch harness, or a poor electrical connection in the Ignition On/Start Switch circuit. To fix the issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

Wrap Up
If your engine light is on due to fault code p2535, check for a faulty ignition onstart switch, open or shorted harness, poor electrical connection, or a faulty body control module.
Visually inspect related wiring harness and connectors for damage or corrosion.
Look for broken, bent, pushed out, or corroded connector’s pins.