The P2308 fault code in automobiles indicates a problem with the ignition coil ‘C’.
The engine light may turn on and the engine may run rough due to a faulty ignition coil or poor electrical connection in the circuit.
It is important to visually inspect the wiring harness and connectors for any damage or corrosion. The repair time for this issue is estimated to be around 1.0. To interpret the fault code, one must check the possible causes listed above and look for any broken or bent components.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
P2308: Unstable Engine? Check These Symptoms Now!
If you notice the engine light on or the engine running rough, it could be a sign of an automobile fault code, such as p2308.
- The P2308 fault code in an automobile can cause the following symptoms: the engine light will turn on or the service engine soon warning light will appear.
- The engine may start running rough, causing a noticeable decrease in performance.
- The vehicle may also experience a lack of power or acceleration.
- Additionally, the engine may misfire or stall, and there may be a noticeable decrease in fuel efficiency.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
P2308: Ignition Coil Circuit Causes
The automobile fault code P2308 can be caused by a faulty ignition coil, open or shorted harness, or poor electrical connection.
- The automobile fault code P2308 can be caused by a faulty ignition coil ‘C’.
- It can also be caused by an open or shorted ignition coil ‘C’ harness.
- Additionally, a poor electrical connection in the ignition coil ‘C’ circuit can also trigger this fault code.
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Fix Code P2308: Simple Steps To Get Your Car Running
To fix the p2308 automobile fault code, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.
- To fix the automobile fault code p2308, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors.
- Look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
- Ensure that everything is in good condition.
- The estimated repair time for this fix is 1.0 hour.
P2308: Affordable Fix For Complex Auto Fault
The fault code P2308 indicates an issue with the ignition coil circuit.
The diagnosis process involves checking the wiring and connections, as well as testing the ignition coil and related components.
The estimated repair time for this issue is 1.0 hour.
The cost of fixing this issue can vary depending on the hourly rate of the auto repair shop, which typically ranges between $75 and $150 per hour. Other factors that may influence the cost include the need for replacement parts and any additional repairs that may be required.
P2308: Ignition Coil ‘c’ Secondary Circuit – High
The P2308 code is related to the ignition coil in a vehicle. The Powertrain Control Module controls the current flow through the primary ignition coil. The PCM provides a switched ground path through the ignition coil driver to ground.
The code sets when the PCM detects a short to voltage in the circuit. The code specifically refers to the ignition coil ‘C’ secondary circuit.
FAQ
If you’re experiencing the P2308 fault code in your automobile, you may notice the engine light or service engine soon warning light is on, and the engine may be running rough. This fault code is typically caused by a faulty ignition coil ‘C’, an open or shorted ignition coil ‘C’ harness, or a poor electrical connection in the ignition coil ‘C’ circuit. To fix the issue, it’s recommended to visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing a rough running engine and the engine light is on, it could be due to a faulty ignition coil ‘C’, an open or shorted harness, or a poor electrical connection. To fix the P2308 fault code, visually inspect the related wiring harness and connectors for any damaged components, broken, bent, pushed out, or corroded connector’s pins. Check the possible causes listed above to ensure a proper fix.
The P2308 fault code in an automobile is indicated by the Engine Light ON or Service Engine Soon Warning Light. The engine may also be running rough. This fault code is caused by a faulty Ignition Coil ‘C’, an open or shorted Ignition Coil ‘C’ harness, or a poor electrical connection in the Ignition Coil ‘C’ circuit. To fix this issue, one should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light and the engine is running rough, it could be due to a faulty Ignition Coil ‘C’, an open or shorted harness, or poor electrical connection.
Check the wiring harness and connectors for damage and inspect the components for any issues.
