The automobile fault code P1626 indicates a problem with the ignition switch.
When this fault occurs, the engine light or service engine soon warning light will turn on. The possible causes include a faulty ignition switch, an open or shorted ignition switch harness, a poor electrical connection in the ignition switch circuit, or the use of an incorrect ignition key.
To fix this issue, you should visually inspect the wiring harness and connectors, checking for any damage or broken, bent, pushed out, or corroded pins in the connectors.
The repair time for this fault is estimated to be around 1.0.
To interpret the fault code, you can refer to the “Possible Causes” listed above and perform the necessary inspections and repairs.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
Unveiling The Mystery: Symptoms Of Fault Code P1626 Revealed!
When the engine light is on or the service engine soon warning light is illuminated, it could be a sign of the p1626 fault code.
- The symptoms of the automobile fault code p1626 include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.
Unraveling The Mystery: What Causes Fault Code P1626?
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
The automobile fault code p1626 can be caused by a faulty ignition switch, open or shorted ignition switch harness, poor electrical connection in the ignition switch circuit, or an incorrect ignition key.
- The fault code P1626 can be caused by a faulty ignition switch, an open or shorted ignition switch harness, a poor electrical connection in the ignition switch circuit, or the use of an incorrect ignition key.
Fixing Code P1626: Simple Steps To Resolve The Issue
To fix the automobile fault code p1626, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.
- To fix the automobile fault code p1626, you need to follow these steps: 1.
- Check the possible causes mentioned above.
- 2.
- Visually inspect the wiring harness and connectors related to the fault code.
- 3.
- Look for any damaged components.
- 4.
- Check for broken, bent, pushed out, or corroded pins in the connectors.
- The estimated repair time for this fix is 1.0 hour.
Cracking The Code: P1626 Fixing Cost And Complexity Unveiled!
The factors influencing the diagnosis and fixing cost of automobile fault code p1626 are the estimated repair time of 1.0 hour and the average hourly rate charged by auto repair shops, which ranges between $75 and $150.
P1626 Fault Code: Understanding The Description And Troubleshooting Steps
The P1626 fault code is related to the theft deterrent fuel enable signal in the automobile’s Body Control Module (BCM). This signal is produced when the ignition is ON and the correct key resistor pellet is detected. The Powertrain Control Module (PCM) monitors this signal during crank.
If the PCM detects that the fuel enable signal is not present or incorrect while the engine is running, the P1626 code will be set.
Depending on when the loss of the fuel enable signal was detected, the P1626 code can cause either a no-start condition or normal operation. If the condition occurred after the BCM sensed the proper key resistor pellet and signaled the PCM to continue fuel delivery, the engine will continue to start and run. However, if the condition occurred before the BCM sensed the proper key resistor pellet, the engine will start and immediately stall.
In this case, the PCM will inhibit fuel delivery and the BCM will disable the starter. In summary, the P1626 code indicates a problem with the theft deterrent fuel enable signal, which can result in a no-start condition or engine stalling.
It is important to diagnose and fix this issue to ensure proper fuel delivery and engine operation.
FAQ
If you see the engine light or service engine soon warning light on, the fault code P1626 could be the culprit. This code is often caused by a faulty ignition switch, an open or shorted ignition switch harness, a poor electrical connection in the ignition switch circuit, or even an incorrect ignition key. To fix this issue, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins. Don’t forget to check the possible causes mentioned above for a more comprehensive solution.
If you’re dealing with the P1626 fault code and your engine light is on, it’s time to take action. The culprit could be a faulty ignition switch, an open or shorted ignition switch harness, a poor electrical connection in the ignition switch circuit, or even an incorrect ignition key. To fix this issue, start by visually inspecting the wiring harness and connectors. Look for any signs of damage, such as broken, bent, pushed out, or corroded pins. Don’t forget to check for any damaged components as well. It’s crucial to address these possible causes to get your engine running smoothly again.
When resolving the P1626 fault code, start by checking for damaged components and corroded connector pins. This can be done by visually inspecting the related wiring harness and connectors. Look for any broken, bent, pushed out, or corroded pins. These issues can cause a poor electrical connection and lead to the engine light being on. By addressing these potential causes, you can effectively fix the problem and ensure smooth engine performance.
Wrap Up
If your engine light is on or you see the service engine soon warning light, it could be due to a faulty ignition switch, an open or shorted ignition switch harness, a poor electrical connection in the ignition switch circuit, or using the incorrect ignition key. To fix this issue, visually inspect the wiring harness and connectors, check for damaged components, and look for any broken, bent, pushed out, or corroded connector pins.
