The automobile fault code P0796 indicates a problem with the pressure control solenoid valve ‘C’ in the transmission. Symptoms may include erratic shifting, slipping, or no shifting at all. The most common causes are low transmission fluid level, dirty transmission fluid, a faulty pressure control solenoid valve ‘C’, or issues with the wiring harness or electrical connections.
It is important to address this issue promptly as it can lead to further damage to the transmission. Repairing the problem involves visually inspecting the wiring harness and connectors, checking for damaged components, and ensuring the connectors’ pins are not broken, bent, pushed out, or corroded.
The repair time for this issue is estimated to be around 1.0 hour. To interpret the fault code, it is recommended to check the “Possible Causes” listed above and perform the necessary inspections and repairs.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
The fault code on your car’s dashboard isn’t always reliable. That’s why it’s smart to keep an OBD scanner in your toolbox for quick, accurate diagnostics.
Decode The Symptoms Of Code P0796: Unveiling The Culprit!
Experiencing issues with your vehicle’s transmission? Check out the symptoms of fault code P0796 below.
- The symptoms of the automobile fault code P0796 include: delayed or harsh shifting between gears, slipping or erratic shifting, transmission overheating, decreased fuel efficiency, illuminated check engine light, and reduced engine power.
Unveiling The Culprits: What Causes Fault Code P0796?
The fault code p0796 can be caused by a low transmission fluid level, dirty fluid, faulty pressure control solenoid valve ‘C’, and more.
- The fault code P0796 can be caused by the following factors: low transmission fluid level, dirty transmission fluid, faulty pressure control solenoid valve ‘C’, open or shorted harness of pressure control solenoid valve ‘C’, and poor electrical connection in the circuit of pressure control solenoid valve ‘C’.
It’s best not to rely on the car’s display for fault codes. Decoding the fault code is more accurate and reliable if you use a digital OBD scanner.
Fixing Code P0796: Step-By-Step Guide To Resolve Transmission Pressure Control Solenoid C Circuit Range/Performance
To fix the p0796 fault code, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.
- To fix the automobile fault code P0796, start by checking the possible causes mentioned above.
- Then, visually inspect the wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded pins in the connectors.
- This fix should take approximately 1.0 hour.
Cracking The Code: P0796 – Cost And Complexity Unveiled!
The factors influencing the diagnosis and fixing cost of the automobile fault code p0796 are the estimated repair time of 1.0 hour and the average hourly rate charged by auto repair shops, which ranges between $75 and $150.
Decode The Mystery: When Does Code P0796 Strike?
The fault code P0796 indicates a discrepancy between the gear required by the Engine Control Module (ECM) and the actual gear being used while driving.
This means that the ECM is expecting the vehicle to be in a specific gear, but the actual gear being used does not match this expectation. This can lead to issues with the vehicle’s performance and can cause problems with shifting gears smoothly.
It is important to address this fault code promptly to ensure proper functioning of the transmission system.
FAQ
The fault code P0796 in an automobile can be caused by various factors. These include a low transmission fluid level, dirty transmission fluid, a faulty pressure control solenoid valve ‘C’, an open or shorted harness for the pressure control solenoid valve ‘C’, or a poor electrical connection in the pressure control solenoid valve ‘C’ circuit. To fix this issue, it is recommended to visually inspect the wiring harness and connectors, check for any damaged components, and look for broken, bent, pushed out, or corroded pins in the connectors.
To fix the P0796 fault code, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check if there are any broken, bent, pushed out, or corroded pins in the connectors. This can help identify if there is an open or shorted circuit or a poor electrical connection causing the issue. Don’t forget to also check the other possible causes like low transmission fluid level, dirty transmission fluid, or a faulty pressure control solenoid valve ‘C’.
To resolve the P0796 fault code, start by checking for the following: low transmission fluid level, dirty transmission fluid, a faulty pressure control solenoid valve ‘C’, an open or shorted pressure control solenoid valve ‘C’ harness, or a poor electrical connection in the pressure control solenoid valve ‘C’ circuit. Visually inspect the wiring harness and connectors, looking for any damaged components and broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
To fix the P0796 fault code, start by checking the transmission fluid level and ensuring it is not low or dirty.
Next, inspect the pressure control solenoid valve ‘C’ and its wiring harness for any damage or poor electrical connections.
Look for broken, bent, pushed out, or corroded pins on the connectors.
