The automobile fault code P0697 indicates a problem with the Engine Control Module (ECM).
The most common symptom is the Engine Light being ON or the Service Engine Soon Warning Light. The cause of this fault code can be a faulty ECM, an open or shorted ECM harness, poor electrical connection in the ECM circuit, or a shorted sensor on the 5-volt circuit. To fix this issue, you should visually inspect the wiring harness and connectors, checking for any damage or corrosion.
Look out for broken, bent, pushed out, or corroded pins in the connectors.
The repair time for this issue is estimated to be around 1.0. It is important to address this fault code promptly to prevent further damage to the vehicle.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
Unveiling The Symptoms Of Fault Code P0697: A Troubleshooting Guide
When the engine light is on or the service engine soon warning light is illuminated, it could be a sign of the p0697 fault code.
- The symptoms of the automobile fault code p0697 include the Engine Light being ON or the Service Engine Soon Warning Light being illuminated.
Unveiling The Culprits: What Causes Fault Code P0697?
The automobile fault code p0697 can be caused by a faulty ECM, open or shorted ECM harness, poor electrical connection in the ECM circuit, or a shorted sensor on the 5 volt circuit.
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
- The fault code p0697 can be caused by a faulty Engine Control Module (ECM), an open or shorted ECM harness, a poor electrical connection in the ECM circuit, or a shorted sensor on the 5 volt circuit.
Fixing Code P0697: Simple Steps To Resolve The Issue!
To fix the p0697 fault code, start by visually inspecting the wiring harness, connectors, and components for any damage or corrosion.
- To fix the automobile fault code p0697, start by checking the possible causes mentioned above.
- Then, visually inspect the wiring harness and connectors related to the issue.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.
- This fix is estimated to take approximately 1.0 hour.
Cracking The Code: P0697 – Cost And Complexity Unveiled!
The factors influencing the diagnosis and fixing cost of the automobile fault code p0697 are the estimated repair time and the hourly rate charged by auto repair shops.
The estimated repair time for this fault code is 1.0 hour. Auto repair shops typically charge between $75 and $150 per hour for their services. These factors will determine the overall cost of diagnosing and fixing the p0697 fault code.
P0697: Fuel Pump Control Circuit Low – Understanding The Issue
The P0697 fault code refers to a problem with the Sensor Reference Voltage ‘C’ Circuit O in the control module of your automobile.
The control module has internal 5-volt reference buses that provide a 5-volt reference circuit for multiple sensors. If there is a fault condition on one 5-volt reference circuit, it can affect the other circuits connected to the reference bus. The control module constantly monitors the voltage on these reference buses.
The P0697 code indicates an issue with the Sensor Reference Voltage ‘C’ Circuit O specifically.
FAQ
If you see the engine light on or the service engine soon warning light, the fault code P0697 could be the culprit. This code is often caused by a faulty Engine Control Module (ECM), an open or shorted ECM harness, a poor electrical connection in the ECM circuit, or a shorted sensor on the 5 volt circuit. To fix this issue, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins. Don’t forget to check the possible causes mentioned above.
To fix fault code P0697, start by visually inspecting the wiring harness and connectors. Look for any damaged components and check if there are any broken, bent, pushed out, or corroded pins in the connectors. This can help identify if the Engine Control Module (ECM) is faulty, if there is an open or shorted ECM harness, if there is a poor electrical connection in the ECM circuit, or if there is a shorted sensor on the 5 volt circuit. Take a close look and address any issues found to resolve the problem.
When resolving the fault code p0697, start by checking for damaged components and connector’s pins. Visually inspect the related wiring harness and connectors, looking for any signs of damage such as broken, bent, pushed out, or corroded pins. This can help identify if the Engine Control Module (ECM) is faulty, if the ECM harness is open or shorted, if there is a poor electrical connection in the ECM circuit, or if there is a shorted sensor on the 5 volt circuit. Take the necessary steps to fix any issues found during the inspection.
Wrap Up
If your engine light is on and you’re seeing the P0697 fault code, it could be due to a faulty Engine Control Module (ECM), an open or shorted ECM harness, poor electrical connection in the ECM circuit, or a shorted sensor on the 5 volt circuit. To fix this, visually inspect the wiring harness and connectors, check for damaged components, and look for any broken, bent, pushed out, or corroded connector pins.
