The OBD code B2631 for Nissan indicates an issue with the Sunload Sensor circuit.
This affects the Air Condition (A/C) Automatic Amplifier.
Symptoms include the Engine Light being ON.
The code is often caused by a faulty Sunload Sensor or related wiring issues.
It’s not a severe issue but should be addressed.
A possible fix is to inspect and repair any damaged components or wiring connections related to the Sunload Sensor circuit.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Symptoms of the Nissan b2631 OBD Code
The vehicle displays an error code B2631 on the Nissan’s system.
- Symptoms: Service Engine Soon Warning Light ON.
- Intermittent power window operation.
- Vehicle may not start.
- Horn may not work.
- Power door locks may not function.
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Causes of the Nissan b2631 OBD Code
Possible triggers for Nissan B2631 include faulty keyless entry receiver, wiring issues, or damaged key fob.
- B2631 can be caused by a faulty Sunload Sensor.
- A Sunload Sensor harness that is open or shorted.
- A Sunload Sensor circuit with poor electrical connection.
- A faulty Air Condition (A/C) Automatic Amplifier.
Fixing Nissan Error Code b2631 Step By Step
To address Nissan fault code B2631, inspect and repair the ignition relay circuit as needed.
- To fix the Nissan OBDII code B2631, start by reviewing the possible causes mentioned above.
- Visually examine the wiring harness and connectors related to the steering angle sensor circuit.
- Check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.
- If no visible issues are found, perform a diagnostic scan tool steering angle sensor calibration procedure.
- Reset the steering angle sensor memory using a compatible scan tool.
- Test drive the vehicle to ensure the code does not return.
- If the code persists, consider replacing the steering angle sensor following manufacturer guidelines.
Cost Of Fixing Nissan b2631 Fault Code
Diagnosing and repairing Nissan fault code B2631 may involve replacing the keyless entry receiver.
The cost to diagnose and fix Nissan OBD code B2631 typically ranges from $75 to $150, based on a 1. 0hour repair time.
Factors like shop rates and complexity can affect the final cost.
That fault code is a turning point. If repair costs are climbing and your current loan feels like it’s holding you back, this is the time to plan ahead. The free Car Loan Payment Tracker helps you see how quickly you can pay off what’s left—and start preparing, with confidence, for your dream car.
Details of the Nissan b2631 OBD Code
The fault code B2631 in a Nissan indicates an issue with the key switch circuit.
Nissan OBD code B2631 means the key ID in the key is not registered.
This code is triggered by the body control module (BCM) when it detects that the key being used is not programmed or registered in the vehicle’s system.
This code is related to the vehicle’s immobilizer system, which is designed to prevent unauthorized starting of the vehicle.
Mechanic’s Tech Notes
For Nissan B2631, refer to detailed information on the fault code’s causes, symptoms, and solutions.
To diagnose and fix OBDII code B2631 in a Nissan, start by checking the Transmission Control Module (TCM) power and ground using a multimeter.
Verify TCM communication over the Controller Area Network (CAN) using a scan tool.
If the TCM does not respond, reprogramming or reflashing may be necessary.
Visually inspect the wiring harness and connectors for any damage, and check connector pins for signs of being broken, bent, pushed out, or corroded.
This thorough inspection will help identify and address any issues causing the B2631 fault code.
FAQ
OBD code B2631 in a Nissan indicates an issue with the Sunload Sensor circuit. Check for faults in the sensor, wiring, or A/C Automatic Amplifier.
Common symptoms of code B2631 in a Nissan include the Engine Light ON, caused by issues like a faulty Sunload Sensor or poor electrical connections.
Diagnose OBD code B2631 in Nissan: Symptoms Engine Light ON; Causes Faulty Sunload Sensor, harness issues, poor connections; Fix Inspect wiring, connectors, and components.
Wrap Up
If your Nissan is displaying OBD code B2631, you may experience issues with the passenger airbag status indicator.
This could be caused by a faulty passenger airbag status indicator circuit, a malfunctioning passenger airbag status indicator sensor, or damaged wiring in the system.
To address Nissan OBD code B2631, start by inspecting the wiring harness and connectors related to the passenger airbag status indicator system.
Test the passenger airbag status indicator sensor for proper operation and replace if necessary.
Ensure all connections are secure and free of corrosion or damage.
