[SOLVED] Jeep P1486 Code: Repair Evap System Pinched Hose Fast

The OBD code P1486 for Jeep indicates a fault with the Leak Detection Pump (LDP) pressure hose being obstructed or a faulty LDP.

Symptoms include the Engine Light ON and a fuel odor due to vapor release.

The issue can be caused by an obstructed hose or EVAP canister.

While not critical, it should be addressed promptly.

A possible fix involves inspecting the wiring harness, connectors, and components for damage.

Repair Importance Level	10.0 (Out of 10)
Estimated Repair Time	Approximately 1.0 hour
Repair Difficulty Level	10.0 (Out of 10)

I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!

Symptoms of the Jeep p1486 OBD Code

The Jeep is experiencing issues with the EVAP system, indicated by fault code P1486.

Symptoms: Engine Light ON.
A noticeable fuel odor may result from fuel vapor release.

Causes of the Jeep p1486 OBD Code

Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)

P1486 in a Jeep is typically triggered by issues with the EVAP system.

P1486 can be caused by an obstructed Leak Detection Pump (LDP) pressure hose.
A faulty Leak Detection Pump (LDP).
An obstructed hose.
An obstructed EVAP canister.

Fixing Jeep Error Code p1486 Step By Step

Replace the faulty EGR solenoid to address Jeep fault code P1486.

To fix Jeep OBDII code P1486, start by reviewing the possible causes mentioned above.
Visually examine the wiring harness and connectors related to the cooling fan relay circuit.
Check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.
Test the cooling fan relay operation and replace it if necessary.
Clear the fault codes from the vehicle’s computer using a scan tool.
Finally, perform a road test to ensure the issue has been resolved.

Cost Of Fixing Jeep p1486 Fault Code

The repair for Jeep fault code P1486 may involve replacing the evaporative system leak detection pump.

The cost to diagnose and fix Jeep OBD code P1486 depends on the estimated 1. 0hour repair time.

Labor rates usually range from $75 to $150 per hour, so the total cost could be between $75 and $150. The final cost may vary based on shop rates and the complexity of the repair.

Details of the Jeep p1486 OBD Code

Code P1486 in a Jeep indicates a problem with the Evaporative Emission System Purge Control Valve Circuit.

OBD code P1486 for Jeep vehicles indicates a problem with the Evaporative Emission System Purge Control Valve Circuit.

This code is triggered by the Engine Control Module (ECM) when it detects an electrical fault in the circuit related to the purge control valve.

The purge control valve is part of the evaporative emissions system, which helps control the release of fuel vapors from the fuel tank into the engine for combustion.

When this circuit malfunctions, it can affect the proper operation of the evaporative emissions system, leading to increased emissions and potential drivability issues.

Mechanic’s Tech Notes

Detailed information on diagnosing and repairing fault code P1486 in a Jeep vehicle.

To diagnose and fix OBDII code P1486 on a Jeep, start by checking the Transmission Control Module (TCM) power and ground using a multimeter.

Verify TCM communication over the Controller Area Network (CAN) using a scan tool.

If the TCM does not respond, reprogramming or reflashing may be necessary.

Visually inspect the wiring harness and connectors for any damage, and ensure connector pins are not broken, bent, pushed out, or corroded.

Address any issues found during the inspection to resolve the P1486 fault code.

FAQ

1. What does OBD code P1486 mean in a Jeep vehicle?

OBD code P1486 in a Jeep indicates a fault with the Leak Detection Pump (LDP) system. Check LDP components, hoses, and wiring for issues.

2. What are the common symptoms associated with OBD code P1486 in a Jeep?

Common symptoms of OBD code P1486 in a Jeep include Engine Light ON, fuel odor, caused by issues with Leak Detection Pump (LDP) system. Fix involves inspecting related components.

3. How can I diagnose and fix OBD code P1486 in my Jeep vehicle?

Diagnose P1486 in Jeep: Check LDP pressure hose, LDP, EVAP canister for obstructions. Inspect wiring, connectors for damage, corrosion. Fix as needed.

Wrap Up

If your Jeep is displaying OBD code P1486 and you notice issues with the EVAP system, it could be caused by a faulty leak detection pump pressure switch, a leak in the EVAP system, or a problem with the wiring harness or connectors related to the EVAP system.

To address Jeep OBD code P1486, start by inspecting the wiring harness and connectors for any signs of damage or corrosion.

Test the leak detection pump pressure switch for proper operation and check for any leaks in the EVAP system that may need to be repaired.