[SOLVED] Jeep P0345 Code: Fast Fix For Camshaft Position Sensor

The OBD code P0345 for a Jeep indicates a problem with the Camshaft Position Sensor A Circuit.

Symptoms include the Engine Light ON, lack of power, and engine stalling.

Causes may include low engine oil, a faulty CMP sensor, wiring issues, or a problematic PCM.

This issue should be addressed promptly to prevent further damage.

A possible fix involves inspecting and repairing any damaged components or wiring connections related to the camshaft position sensor.

Repair Importance Level	10.0 (Out of 10)
Estimated Repair Time	Approximately 1.0 hour
Repair Difficulty Level	10.0 (Out of 10)

I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!

Symptoms of the Jeep p0345 OBD Code

The vehicle may experience rough idling or stalling due to fault code P0345 on a Jeep.

With Jeep OBD code P0345, the Engine Light will be ON.
Lack of Power may be experienced.
Engine Stall can occur.

Causes of the Jeep p0345 OBD Code

Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)

Possible reasons for Jeep fault code P0345 include camshaft position sensor circuit malfunction.

P0345 in a Jeep can be caused by low engine oil.
A faulty Camshaft Position (CMP) Sensor.
An open or shorted Camshaft Position Sensor harness.
A poor electrical connection in the Camshaft Position Sensor circuit.
A faulty Powertrain Control Module (PCM).
A loose/damaged or misaligned Camshaft Tone Wheel.
Or a dead (weak) battery.

Fixing Jeep Error Code p0345 Step By Step

Replace the camshaft position sensor on the Jeep to address fault code P0345.

To fix a Jeep OBDII code P0345, start by reviewing the possible causes mentioned above.
Visually examine the camshaft position sensor and its wiring harness for any damage.
Check the connector pins for signs of being broken, bent, pushed out, or corroded.
Replace the camshaft position sensor if any issues are found during inspection.
Clear the fault codes from the vehicle’s computer using a scan tool.
Test drive the vehicle to ensure the code does not return, indicating a successful repair.

Cost Of Fixing Jeep p0345 Fault Code

The repair for Jeep fault code P0345 involves diagnosing and replacing the camshaft position sensor.

The cost to diagnose and fix a Jeep OBD code P0345 typically ranges from $75 to $150 per hour for labor rates.

With an estimated repair time of 1. 0 hour, the total cost can be around $75 to $150, depending on shop rates and the complexity of the repair.

Details of the Jeep p0345 OBD Code

Fault code P0345 in a Jeep indicates a problem with the camshaft position sensor circuit.

OBD code P0345 for a Jeep means that a malfunction has been detected in the camshaft position sensor A circuit bank 2. This code is triggered by the Engine Control Module (ECM) when it detects a discrepancy between the camshaft position sensor A signal and the crankshaft position sensor signal.

The camshaft position sensor helps the ECM determine the position of the camshaft in relation to the crankshaft for proper engine operation.

When P0345 is set, it indicates an issue with the camshaft position sensor circuit on bank 2 of the engine.

Mechanic’s Tech Notes

Detailed information on resolving Jeep fault code p0345 for camshaft position sensor circuit malfunction.

To diagnose and fix OBDII code P0345 on a Jeep, start by checking the camshaft position sensor’s wiring harness and connector for any damage or corrosion.

Use a voltmeter to test the sensor’s power and ground connections.

Verify the sensor’s signal using a scan tool to ensure proper operation.

If the wiring and connections are intact, consider replacing the camshaft position sensor itself.

Additionally, check for any timing chain issues that could affect sensor readings.

Clear the code after repairs and test drive the vehicle to confirm the issue is resolved.

FAQ

1. What are the symptoms of a P0345 fault code in a Jeep?

Symptoms of P0345 in a Jeep: Engine Light ON, lack of power, engine stall. Causes: Faulty CMP sensor, wiring issues. Fix: Inspect wiring, connectors, and CMP sensor for damage.

2. What is the typical cause of a P0345 fault code in a Jeep vehicle?

A typical cause of a P0345 fault code in a Jeep could be a faulty Camshaft Position Sensor, open/shorted harness, or PCM issue. Check wiring and connectors for damage.

3. How can I diagnose and repair a P0345 fault code in my Jeep?

Diagnose P0345 in Jeep: Check CMP sensor, wiring, PCM. Look for oil level, battery issues. Inspect camshaft tone wheel. Repair as needed.

Wrap Up

If your Jeep is displaying OBD code p0345 and experiencing rough idling or stalling, it may be caused by a faulty camshaft position sensor, damaged wiring in the sensor circuit, or low engine oil levels affecting sensor performance.

To address Jeep OBD code p0345, check the camshaft position sensor for proper operation, inspect the sensor wiring for any breaks or corrosion, and ensure the sensor connector is securely attached.

Consider replacing the camshaft position sensor if necessary to resolve the issue.