[SOLVED] Jeep P0320 Code: Quick Fix For Pcm Crank Signal

The OBD code P0320 for Jeep indicates an issue with the Crankshaft Position Sensor (CKP) circuit.

Symptoms include the Engine Light ON, lack of power, difficult starting, or engine stumbling/stalling.

Causes may include a faulty CKP sensor, wiring harness issues, or a faulty PCM.

This is a serious issue that requires immediate attention.

A possible fix involves inspecting and repairing any damaged wiring or connectors related to the CKP sensor.

Repair Importance Level	10.0 (Out of 10)
Estimated Repair Time	Approximately 1.0 hour
Repair Difficulty Level	10.0 (Out of 10)

Symptoms of the Jeep p0320 OBD Code

The Jeep is experiencing issues with the ignition/distributor engine speed input circuit.

With Jeep OBD code P0320, the Engine Light will be ON.
Lack/Loss of Power may be experienced.
The engine may be harder to start.
The engine may stumble or stall.

Causes of the Jeep p0320 OBD Code

Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)

Possible reasons for Jeep fault code P0320 include issues with the ignition/distributor engine speed input circuit.

Causes: Faulty Crankshaft Position Sensor (CKP).
Crankshaft Position Sensor (CKP) harness is open or shorted.
Crankshaft Position Sensor (CKP) circuit poor electrical connection.
Faulty Powertrain Control Module (PCM).

Fixing Jeep Error Code p0320 Step By Step

Replace faulty crankshaft position sensor to resolve Jeep fault code P0320.

To fix a Jeep OBDII code P0320, start by reviewing the possible causes related to the crankshaft position sensor circuit.
Visually inspect the wiring harness and connectors for any damage or corrosion.
Check the connector pins for any signs of being broken, bent, or pushed out.
Test the crankshaft position sensor for proper operation and replace if necessary.
Clear the fault code from the vehicle’s computer using a scan tool.
Finally, road test the vehicle to ensure the code does not return, indicating a successful repair.

Cost Of Fixing Jeep p0320 Fault Code

Diagnosing and repairing fault code P0320 on a Jeep involves testing and potentially replacing the crankshaft position sensor.

The cost to diagnose and fix a Jeep OBD code P0320 depends on the estimated 1. 0hour repair time.

Labor rates usually range from $75 to $150 per hour, so the general cost could be between $75 and $150. Factors like shop rates and the complexity of the issue can affect the final cost.

That fault code is a turning point. If repair costs are climbing and your current loan feels like it’s holding you back, this is the time to plan ahead. The free Car Loan Payment Tracker helps you see how quickly you can pay off what’s left—and start preparing, with confidence, for your dream car.

Details of the Jeep p0320 OBD Code

Fault code P0320 in a Jeep indicates an issue with the ignition/distributor engine speed input circuit malfunction.

OBD code P0320 for a Jeep means that there is an issue with the ignition/distributor engine speed input circuit.

This code is triggered by the Engine Control Module (ECM) when it does not receive a proper engine speed signal from the ignition system.

In simpler terms, this code indicates a problem with the crankshaft position sensor or the wiring associated with it.

The crankshaft position sensor is responsible for providing the ECM with information about the engine’s speed and position, which is crucial for proper ignition timing and fuel delivery.

When P0320 is set, it typically points to a faulty crankshaft position sensor, damaged wiring/connectors related to the sensor, or issues with the sensor’s reluctor ring.

It’s important to inspect these components carefully to determine the exact cause of the problem and proceed with the necessary repairs.

Mechanic’s Tech Notes

For Jeep code P0320, check the crankshaft position sensor circuit for faults or failures.

For Jeep OBDII code P0320 (Ignition/Distributor Engine Speed Input Circuit Malfunction), start by checking the crankshaft position sensor (CKP) and its wiring harness for any damage or loose connections.

Use a voltmeter to test the CKP sensor’s resistance and voltage output.

Ensure the sensor is properly aligned and has the correct air gap.

If the sensor checks out, inspect the power and ground connections to the Engine Control Module (ECM) for any issues.

A scan tool can help monitor the CKP sensor’s signal while the engine is running to pinpoint any irregularities.

Reflashing the ECM may be necessary if all components check out.

FAQ

1. What are the common causes of OBD code P0320 in a Jeep vehicle?

Common causes of OBD code P0320 in a Jeep: Faulty CKP sensor, open/shorted CKP harness, poor CKP circuit connection, faulty PCM. Inspect wiring and connectors for damage.

2. How can I diagnose and fix OBD code P0320 in my Jeep?

Diagnose P0320 in Jeep: Check Crankshaft Position Sensor, harness, and PCM. Inspect wiring for damage or poor connection. Repair as needed.

3. Is it safe to continue driving my Jeep with a P0320 fault code present?

It is not safe to continue driving with a P0320 code. The fault may cause engine issues like stalling. Inspect and repair the CKP sensor and related components.

Wrap Up

If your Jeep is experiencing stalling, rough idling, or difficulty starting, the OBD code P0320 may indicate a faulty crankshaft position sensor, damaged wiring harness, or poor sensor connection.

These issues can disrupt the engine’s timing and cause performance problems.

To address Jeep’s P0320 code, inspect the crankshaft position sensor and its wiring for any signs of damage or corrosion.

Test the sensor’s resistance and ensure proper connection to the engine control module.

Replace the sensor if necessary and repair any damaged wiring to restore proper engine operation.