[SOLVED] Dodge U140D Code: Fast Fix For Wheel Speed Signal

The OBD code U140D for Dodge indicates a communication issue with the Electronic Limited Slip Differential (ELSD) Module.

Symptoms include the Engine Light being ON.

Causes may include ABS Module or BCM codes, faulty ELSD Module, open/shorted harness, or poor electrical connection.

This is a moderate issue.

A possible fix is to check for damaged components and inspect wiring harness/connectors for any issues.

Repair Importance Level	10.0 (Out of 10)
Estimated Repair Time	Approximately 1.0 hour
Repair Difficulty Level	10.0 (Out of 10)

Symptoms of the Dodge u140d OBD Code

The Dodge U140D fault code typically triggers when there is a communication issue with the Implausible Vehicle Configuration Data.

Symptoms: Service Electronic Throttle Control warning light may illuminate.
Possible loss of throttle response.
Difficulty shifting gears.
Rough or erratic engine idle.
Engine stalling at low speeds.

Causes of the Dodge u140d OBD Code

Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)

Possible triggers for Dodge fault code U140D include issues with the Implausible Data Received from Electronic Control Unit (ECU).

U140D can be caused by a faulty Electronic Limited Slip Differential (ELSD) Module.
Check for Antilock Brake System (ABS) Module codes.
Check for Body Control Module (BCM) codes.
The Electronic Limited Slip Differential Module harness may be open or shorted.
Look for a poor electrical connection in the Electronic Limited Slip Differential Module circuit.

Fixing Dodge Error Code u140d Step By Step

Address the issue by inspecting the wiring harness for any damage or loose connections.

To fix the Dodge OBDII code U140D, start by reviewing the possible causes mentioned above.
Visually examine the wiring harness and connectors related to the ABS module.
Check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.
If any issues are found, repair or replace the damaged wiring or connectors.
Perform a reset on the ABS module to clear the code.
Test drive the vehicle to see if the code returns.
If the code persists, consider replacing the ABS module with a new one.

Cost Of Fixing Dodge u140d Fault Code

Diagnosing and repairing Dodge code U140D may involve inspecting and replacing the transmission control module.

The cost to diagnose and fix the Dodge OBD code U140D depends on the estimated 1. 0hour repair time.

Labor rates usually range from $75 to $150 per hour, so the total cost will likely be between $75 and $150, depending on shop rates and the complexity of the repair.

That fault code is a turning point. If repair costs are climbing and your current loan feels like it’s holding you back, this is the time to plan ahead. The free Car Loan Payment Tracker helps you see how quickly you can pay off what’s left—and start preparing, with confidence, for your dream car.

Details of the Dodge u140d OBD Code

Dodge U140D code indicates a implausible vehicle configuration data received from the steering angle sensor.

Dodge OBD code U140D means Implausible Engine Torque Signal Received.

This code is triggered by the Powertrain Control Module (PCM) when it detects a discrepancy between the expected engine torque signal and the actual signal received from various sensors such as the throttle position sensor, accelerator pedal position sensor, or other related components.

This code is related to the engine torque management system and can be caused by issues such as sensor malfunctions, wiring problems, or software glitches within the PCM.

Mechanic’s Tech Notes

This code indicates a implausible vehicle configuration data error in a Dodge vehicle.

To diagnose and fix OBDII code U140D on a Dodge, start by checking the Transmission Control Module (TCM) power and ground using a multimeter.

Verify TCM communication over the Controller Area Network (CAN) network with a scan tool.

If the TCM does not respond, reprogramming or reflashing may be necessary.

Visually inspect the wiring harness and connectors for any damage, and check connector pins for signs of being broken, bent, pushed out, or corroded.

This thorough inspection can help identify and address potential issues causing the U140D fault code.

FAQ

1. What does OBD code U140D mean in a Dodge vehicle?

OBD code U140D in a Dodge indicates an issue with the Electronic Limited Slip Differential (ELSD) Module. Check ELSD module and related wiring for faults.

2. How can I diagnose the source of a U140D fault code in my Dodge?

Diagnose U140D code in Dodge: Check ABS Module, BCM codes, ELSD Module. Inspect wiring for open/short circuits, poor connections. Examine connectors for damage/corrosion.

3. What are the common symptoms associated with a U140D trouble code in a Dodge vehicle?

Common symptoms of U140D code in Dodge: Engine Light ON, ABS issues, BCM problems, ELSD module faults. Check ABS and BCM codes, inspect wiring for damage or poor connections.

Wrap Up

If your Dodge is displaying OBD code u140d, you may experience issues with the Electronic Stability Control (ESC) system, such as erratic braking, traction control malfunctions, or ABS problems.

This code typically indicates a communication error between the ESC module and other control modules due to faulty wiring, damaged connectors, or a malfunctioning ESC module.

To address Dodge OBD code u140d, start by inspecting the wiring harness for any visible damage or corrosion.

Test the connectors for proper connection and continuity.

If no issues are found, consider replacing the ESC module to resolve the communication error within