[SOLVED] Dodge P2008 Code: Quick Fix For Intake Manifold Runner Control

The OBD code P2008 for Dodge indicates a problem with the intake manifold runner control system.

Symptoms include the Engine Light being ON.

This code is commonly caused by intake manifold runner binding or sticking, faulty manifold flow valve, or issues with the manifold flow valve harness.

It is important to address this issue promptly to prevent further damage.

A possible fix is to inspect the wiring harness and connectors for any damage or poor connections.

Repair Importance Level	10.0 (Out of 10)
Estimated Repair Time	Approximately 1.0 hour
Repair Difficulty Level	6.67 (Out of 10)

Symptoms of the Dodge p2008 OBD Code

The Dodge P2008 fault code typically triggers when there is an issue with the intake manifold runner control circuit.

Symptoms: Engine Light ON.
Reduced engine performance.
Loss of power during acceleration.

Causes of the Dodge p2008 OBD Code

Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)

The Dodge P2008 code typically indicates a problem with the intake manifold runner control circuit.

P2008 can be caused by intake manifold runner binding or sticking.
Faulty manifold flow valve.
Manifold flow valve harness is open or shorted.
Manifold flow valve circuit poor electrical connection.

Fixing Dodge Error Code p2008 Step By Step

Address the intake manifold runner control circuit open for Dodge P2008.

To fix the Dodge OBDII code P2008, start by reviewing the possible causes mentioned above.
Visually examine the corresponding wiring harness and connectors for any damage.
Inspect the connector pins for signs of being broken, bent, pushed out, or corroded.
Check the operation of the intake manifold runner control (IMRC) actuator.
Replace the IMRC actuator if it is faulty.
Clear the fault codes and perform a test drive to verify the repair.
If the code returns, further diagnosis may be needed to identify any underlying issues.

Cost Of Fixing Dodge p2008 Fault Code

Diagnosing and repairing Dodge code P2008 typically involves inspecting and servicing the intake manifold runner control system.

The cost to diagnose and fix a Dodge OBD code P2008 typically ranges from $75 to $150, based on a 1. 0hour repair time.

Factors like shop rates and complexity can affect the final cost.

That fault code is a turning point. If repair costs are climbing and your current loan feels like it’s holding you back, this is the time to plan ahead. The free Car Loan Payment Tracker helps you see how quickly you can pay off what’s left—and start preparing, with confidence, for your dream car.

Details of the Dodge p2008 OBD Code

Dodge P2008 code indicates a problem with the intake manifold runner control circuit.

Dodge OBD code P2008 means that the intake manifold runner control circuit has low voltage.

This code is triggered by the Engine Control Module (ECM) when it detects a voltage signal below the specified range from the intake manifold runner control circuit.

The intake manifold runner control system is responsible for adjusting the length of the intake runners to optimize engine performance at different RPM ranges.

When the voltage signal is low, it can affect the proper operation of this system, leading to drivability issues.

Mechanic’s Tech Notes

Detailed information on Dodge code P2008, including symptoms, causes, and solutions for efficient troubleshooting.

To diagnose and fix OBDII code P2008 in a Dodge, start by checking the throttle actuator control module (TCM) power and ground using a multimeter.

Verify TCM communication over the Controller Area Network (CAN) using a scan tool.

If communication issues are found, reprogramming or reflashing the TCM may be necessary.

Additionally, inspect the wiring harness and connectors for any damage, and ensure connector pins are not broken, bent, pushed out, or corroded.

By following these steps, you can pinpoint the root cause of the P2008 trouble code and address it effectively.

FAQ

1. What are the common symptoms associated with OBD code P2008 in a Dodge vehicle?

Common symptoms of OBD code P2008 in a Dodge vehicle include Engine Light ON, caused by issues like intake manifold runner binding or sticking. Fix involves inspecting wiring and connectors.

2. What is the typical cause of OBD code P2008 in a Dodge vehicle?

OBD code P2008 in a Dodge is typically caused by intake manifold runner binding, faulty manifold flow valve, or issues with the manifold flow valve circuit.

3. How can I diagnose and fix OBD code P2008 in my Dodge vehicle?

Diagnose and fix OBD code P2008 in Dodge: Symptoms Engine Light ON. Causes Intake Manifold Runner issues. Fix Inspect wiring, connectors, and components for damage or corrosion.

Wrap Up

If your Dodge is displaying OBD code P2008, you may experience issues like poor engine performance, rough idling, or decreased fuel efficiency.

This code typically indicates a problem with the intake manifold runner control circuit, possibly caused by a faulty intake manifold runner control actuator, damaged wiring, or a poor electrical connection.

To address Dodge OBD code P2008, start by inspecting the wiring harness and connectors related to the intake manifold runner control actuator.

Test the actuator for proper operation and replace it if necessary.

Ensure all electrical connections are secure and free of corrosion to resolve the