[SOLVED] Dodge P1763 Code: Governor Pressure Sensor High Quick Fix

The OBD code P1763 for Dodge indicates a problem with the Governor Pressure Sensor in the transmission system.

Symptoms include the Engine Light being ON.

This issue is commonly caused by a faulty sensor, open/shorted sensor harness, or poor electrical connection.

It is crucial to visually inspect the wiring harness and connectors for damage or corrosion.

Fix the problem by addressing the possible causes mentioned and checking the connector pins for any issues.

Repair Importance Level	10.0 (Out of 10)
Estimated Repair Time	Approximately 1.0 hour
Repair Difficulty Level	10.0 (Out of 10)

I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!

Symptoms of the Dodge p1763 OBD Code

The vehicle may experience erratic shifting or failure to engage gear with Dodge fault code P1763.

Symptoms: Service Engine Soon Warning Light ON.
Transmission may not shift properly.
Vehicle may go into limp mode where it stays in one gear.
Engine may rev higher than usual during acceleration.

Causes of the Dodge p1763 OBD Code

Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)

Possible reasons for Dodge fault code P1763 include faulty governor pressure sensor, wiring issues, or transmission solenoid problems.

P1763 can be caused by a faulty Governor Pressure Sensor.
A Governor Pressure Sensor harness that is open or shorted.
A Governor Pressure Sensor circuit with poor electrical connection.

Fixing Dodge Error Code p1763 Step By Step

Address the issue by inspecting the transmission control relay circuit for Dodge fault code P1763.

To fix the Dodge OBDII code P1763, start by reviewing the possible causes mentioned above.
Visually examine the wiring harness and connectors related to the transmission solenoid switch valve.
Check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.
Test the transmission solenoid switch valve for proper operation and resistance.
Replace the transmission solenoid switch valve if it is faulty.
Clear the fault codes from the vehicle’s computer using a scan tool.
Test drive the vehicle to ensure the code does not return.

Cost Of Fixing Dodge p1763 Fault Code

The repair for Dodge fault code P1763 typically involves replacing the governor pressure sensor and solenoid.

The cost to diagnose and fix a Dodge OBD code P1763 typically ranges from $75 to $150 per hour for labor rates.

With an estimated repair time of 1. 0 hour, the total cost could be around $75 to $150, depending on shop rates and the complexity of the issue.

Details of the Dodge p1763 OBD Code

Dodge fault code P1763 relates to the Governor Pressure Sensor Voltage Too High.

Dodge OBD code P1763 means the Governor Pressure Sensor Voltage Too High.

This code is triggered by the Powertrain Control Module (PCM) when it detects that the voltage signal from the governor pressure sensor is higher than expected.

The governor pressure sensor is part of the transmission control system in automatic transmissions.

It monitors the hydraulic pressure inside the transmission to help the PCM control shifting and torque converter lockup.

When the voltage signal from this sensor is too high, it can indicate a problem with the sensor itself, the wiring, or the transmission control system.

Mechanic’s Tech Notes

For Dodge code P1763, check for transmission solenoid performance issues causing improper gear ratio.

To diagnose and fix OBDII code P1763 in a Dodge, start by checking the Transmission Control Module (TCM) power and ground using a multimeter.

Verify TCM communication over the Controller Area Network (CAN) using a scan tool.

If the TCM does not respond, reprogramming or reflashing may be necessary.

Visually inspect the wiring harness and connectors for any damage, and ensure connector pins are not broken, bent, pushed out, or corroded.

This thorough inspection can help identify and resolve issues related to code P1763.

FAQ

1. What are the common symptoms associated with OBD code P1763 in a Dodge vehicle?

Common symptoms of OBD code P1763 in a Dodge vehicle include the Engine Light ON and issues with the Governor Pressure Sensor circuit.

2. What is the typical cause of OBD code P1763 in a Dodge vehicle?

The typical cause of OBD code P1763 in a Dodge vehicle is a faulty Governor Pressure Sensor, open/shorted harness, or poor electrical connection.

3. How can I diagnose and fix OBD code P1763 in my Dodge vehicle?

Diagnose and fix OBD code P1763 in your Dodge by checking the Governor Pressure Sensor and its wiring for faults. Inspect connectors for damage or corrosion.

Wrap Up

If your Dodge is displaying OBD code P1763 and experiencing shifting issues, it could be caused by a faulty governor pressure sensor, a damaged wiring harness, low transmission fluid, or a failing transmission control module.

To address Dodge OBD code P1763, check the governor pressure sensor for proper operation, inspect the wiring harness for any signs of damage or corrosion, ensure the transmission fluid level is correct, and test the transmission control module for faults.

Replace any faulty components as needed to resolve the issue.