[SOLVED] Dodge P1062 Code: Quick Fix For Stuck Cylinder 2 Oil Valve

The OBD code P1062 for Dodge indicates an issue with the Variable Valve Actuator (VVA) Solenoid.

Symptoms include the Engine Light being ON.

Causes may include a faulty VVA Solenoid, open/shorted harness, poor electrical connection, or a faulty Powertrain Control Module (PCM).

This is a moderate issue.

A possible fix is to inspect and repair any damaged components or wiring connections related to the VVA Solenoid.

Repair Importance Level	10.0 (Out of 10)
Estimated Repair Time	Approximately 1.0 hour
Repair Difficulty Level	6.67 (Out of 10)

Symptoms of the Dodge p1062 OBD Code

The Dodge fault code P1062 indicates a potential issue with the Manifold Absolute Pressure sensor.

Symptoms: Engine Light ON.
Reduced engine performance.
Rough idle.
Engine stalling.
Hesitation during acceleration.

Causes of the Dodge p1062 OBD Code

Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)

Dodge fault code P1062 typically indicates a problem with the manifold absolute pressure sensor.

P1062 can be caused by a faulty Variable Valve Actuator (VVA) Solenoid.
A Variable Valve Actuator Solenoid harness that is open or shorted.
A Variable Valve Actuator Solenoid circuit with poor electrical connection.
Or a faulty Powertrain Control Module (PCM).

Fixing Dodge Error Code p1062 Step By Step

Address the issue by inspecting the intake manifold runner control system for faults or restrictions.

To fix the Dodge OBDII code P1062, start by reviewing the possible causes mentioned above.
Visually examine the corresponding wiring harness and connectors for any damage.
Check the connector pins for signs of being broken, bent, pushed out, or corroded.
If no issues are found with the wiring and connectors, consider resetting the engine control module (ECM) to clear the code.
Perform a thorough inspection of the intake manifold tuning valve and actuator for any faults or blockages.
Replace the intake manifold tuning valve or actuator if necessary.
Finally, clear the fault code and test drive the vehicle to ensure the issue has been resolved.

Cost Of Fixing Dodge p1062 Fault Code

The repair for Dodge fault code P1062 may involve replacing the intake manifold tuning valve.

The cost to diagnose and fix the Dodge OBD code P1062 typically ranges from $75 to $150, with an estimated repair time of 1. 0 hour.

The total cost depends on labor rates, shop fees, and the complexity of the repair needed.

That fault code is a turning point. If repair costs are climbing and your current loan feels like it’s holding you back, this is the time to plan ahead. The free Car Loan Payment Tracker helps you see how quickly you can pay off what’s left—and start preparing, with confidence, for your dream car.

Details of the Dodge p1062 OBD Code

Dodge fault code P1062 relates to the Manifold Absolute Pressure (MAP) sensor.

Dodge OBD code P1062 means that the Manifold Absolute Pressure (MAP) sensor has detected a voltage signal that is out of range.

This code is triggered by the Engine Control Module (ECM) when it receives a signal from the MAP sensor that is either too high or too low, indicating a potential issue with the sensor or the pressure in the intake manifold.

The MAP sensor is a key component in monitoring the pressure and density of the air entering the engine, providing crucial data for fuel delivery and ignition timing.

When the ECM detects a voltage signal from the MAP sensor that is outside of the expected range, it will trigger the P1062 fault code to alert the driver or technician of a potential problem with the sensor or the intake system.

Mechanic’s Tech Notes

For Dodge code P1062, check for issues with the intake manifold tuning valve.

To diagnose and fix OBDII code P1062 on a Dodge, start by checking the Transmission Control Module (TCM) power and ground using a multimeter.

Verify TCM communication over the Controller Area Network (CAN) network with a scan tool.

If the TCM does not respond, reprogramming or reflashing may be necessary.

Visually inspect the wiring harness and connectors for any damage, and check connector pins for signs of being broken, bent, pushed out, or corroded.

This thorough inspection can help identify and address any issues causing the P1062 fault code.

FAQ

1. What are the common symptoms associated with OBD code P1062 in a Dodge vehicle?

Common symptoms of OBD code P1062 in a Dodge vehicle include Engine Light ON. Causes may be a faulty Variable Valve Actuator (VVA) Solenoid or related wiring issues.

2. What is the typical cause of OBD code P1062 in a Dodge vehicle?

Typical cause of OBD code P1062 in a Dodge: Faulty Variable Valve Actuator (VVA) Solenoid, open/shorted harness, poor connection, or faulty PCM. Inspect and repair wiring/connectors.

3. How can I diagnose and repair OBD code P1062 in my Dodge vehicle?

Diagnose and repair OBD code P1062 in your Dodge by checking VVA solenoid, harness, and PCM. Inspect wiring for damage or poor connections.

Wrap Up

If your Dodge is displaying OBD code P1062, you may experience rough idling, poor acceleration, or stalling.

This code typically indicates an issue with the Manifold Absolute Pressure (MAP) sensor circuit, such as a faulty sensor, damaged wiring, or poor electrical connections.

To address Dodge OBD code P1062, start by inspecting the MAP sensor and its wiring harness for any visible damage.

Test the sensor’s output voltage and ensure proper connection at the sensor and the Engine Control Module (ECM).

Replace the MAP sensor if necessary and repair any damaged wiring or connectors to