The OBD code U140A for Chrysler indicates a fault with the Right Front Wheel Speed Sensor circuit.
Symptoms include the Engine Light being ON.
The cause could be a faulty sensor, open/shorted harness, poor electrical connection, or a faulty ABS Module.
This issue is moderate in severity.
To fix it, inspect the sensor, wiring harness, and connectors for any damage or corrosion.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Symptoms of the Chrysler u140a OBD Code
The vehicle displays a warning light indicating a communication issue with the central gateway module.
- Symptoms: Service Electronic Throttle Control warning light may illuminate.
- Loss of communication with the Front Control Module (FCM) may occur.
- Vehicle may experience drivability issues such as stalling or rough idling.
- Difficulty starting the engine may be noticed.
- The vehicle may go into a limp mode where it operates at reduced power.
Causes of the Chrysler u140a OBD Code
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Possible triggers for Chrysler U140A include faulty wheel speed sensor, damaged wiring, or ABS module issues.
- U140A can be caused by a Faulty Right Front Wheel Speed Sensor.
- A Right Front Wheel Speed Sensor harness that is open or shorted.
- A Right Front Wheel Speed Sensor circuit with poor electrical connection.
- Or a Faulty AntiLock Brake System (ABS) Module.
Fixing Chrysler Error Code u140a Step By Step
Resolve the Chrysler U140A code by inspecting and repairing the Controller Area Network (CAN) bus circuit.
- To fix the Chrysler OBDII code U140A, start by reviewing the possible causes mentioned above.
- Visually examine the wiring harness and connectors related to the ABS module.
- Check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.
- If any issues are found, repair or replace the damaged wiring or connectors as necessary.
- Clear the fault code using a diagnostic scanner.
- Test drive the vehicle to see if the U140A code returns.
- If the code persists, consider resetting the ABS module or performing a software update.
Cost Of Fixing Chrysler u140a Fault Code
Repairing fault code U140A on a Chrysler typically involves diagnosing and fixing a communication issue with the vehicle’s network.
The cost to diagnose and fix the Chrysler OBD code U140A typically ranges from $75 to $150, with an estimated repair time of 1. 0 hour.
The total cost depends on shop rates, complexity of the issue, and any additional parts or labor needed for the repair.
That fault code is a turning point. If repair costs are climbing and your current loan feels like it’s holding you back, this is the time to plan ahead. The free Car Loan Payment Tracker helps you see how quickly you can pay off what’s left—and start preparing, with confidence, for your dream car.
Details of the Chrysler u140a OBD Code
Chrysler U140A code indicates an implausible vehicle configuration data error.
Chrysler OBD code U140A means Implausible Engine Configuration Data Received.
This code is triggered by the Powertrain Control Module (PCM) when it detects that the engine configuration data it is receiving is not valid or makes no sense.
This data is typically received from various sensors and modules in the vehicle to ensure proper engine operation and performance.
When the PCM receives conflicting or incorrect data regarding the engine configuration, it sets this code to alert the technician of a potential issue with the data communication within the vehicle’s network.
Mechanic’s Tech Notes
For Chrysler U140A code, refer to detailed diagnostic information for troubleshooting guidance and solutions.
To diagnose and fix OBDII code U140A in a Chrysler vehicle, start by checking the Transmission Control Module (TCM) power and ground using a multimeter.
Verify TCM communication over the Controller Area Network (CAN) network with a scan tool.
If the TCM does not respond, reprogramming or reflashing may be necessary.
Visually inspect the wiring harness and connectors for any damage, and ensure connector pins are not broken, bent, pushed out, or corroded.
This thorough inspection will help identify and address any issues causing the U140A fault code.
FAQ
OBD code U140A in a Chrysler means an issue with the Right Front Wheel Speed Sensor. Check sensor, harness, connections, and ABS module for faults.
Code U140A in a Chrysler car may cause the Engine Light to come on. Common symptoms include issues with the Right Front Wheel Speed Sensor or ABS Module.
Diagnose U140A in Chrysler: Check Right Front Wheel Speed Sensor, harness, connectors for faults. Inspect ABS Module. Fix: Repair/replace faulty components, ensure good electrical connections.
Wrap Up
If your Chrysler is displaying OBDII code u140a, you may experience issues with the Electronic Stability Control (ESC) system, such as erratic braking, traction control malfunctions, or ABS problems.
This code typically indicates a communication error between the ESC module and other control modules due to faulty wiring, damaged connectors, or a malfunctioning ESC module.
To address Chrysler OBDII code u140a, start by inspecting the wiring harness for any visible damage, ensuring all connectors are securely attached and free of corrosion.
Test the ESC module and related sensors for proper functionality, replacing any components that
