OBD code C0899 indicates a problem with the Battery Voltage Circuit in the Electronic Brake Control Module (EBCM).
Symptoms include the Engine Light being ON.
Causes may include battery voltage issues, a faulty control module, or wiring harness problems.
This issue is moderate in seriousness.
To fix it, inspect the wiring harness and connectors for damage, and check connector pins for any signs of damage.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Symptoms of the c0899 OBD Code
The vehicle displays a warning light indicating a fault with the Electronic Brake Control Module (EBCM).
- Symptoms: Service StabiliTrak Warning Light may illuminate.
- Service Traction Control Warning Light may come on.
- Reduced engine power message may display.
- Steering may feel heavy or difficult to turn.
- Brake pedal may feel spongy or hard.
Causes of the c0899 OBD Code
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Possible triggers for fault code C0899 include issues with the steering angle sensor or related wiring.
- C0899 can be caused by low battery voltage.
- A faulty Control Module.
- An open or shorted Control Module harness.
- Or a poor electrical connection in the Control Module circuit.
Fixing Error Code c0899 Step By Step
To address fault code C0899, inspect the steering angle sensor and related wiring for faults.
- To fix OBDII code C0899, start by reviewing the possible causes mentioned above.
- Visually examine the wiring harness and connectors related to the steering angle sensor system.
- Check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.
- Ensure the steering angle sensor is securely mounted and functioning correctly.
- If no visible issues are found, perform a diagnostic scan tool test to monitor the sensor’s data and operation.
- Replace the steering angle sensor if necessary.
- Clear the fault codes and perform a test drive to verify the repair.
Cost Of Fixing c0899 Fault Code
Diagnosing and repairing fault code C0899 may involve inspecting and replacing the steering angle sensor.
The cost to diagnose and fix OBD code C0899 depends on the estimated 1. 0hour repair time.
Labor rates usually range from $75 to $150 per hour, so the general cost could be between $75 and $150. The final cost may vary based on shop rates and the complexity of the repair.
That fault code is a turning point. If repair costs are climbing and your current loan feels like it’s holding you back, this is the time to plan ahead. The free Car Loan Payment Tracker helps you see how quickly you can pay off what’s left—and start preparing, with confidence, for your dream car.
Details of the c0899 OBD Code
Code C0899 indicates a fault in the Electronic Brake Control Module (EBCM) motor circuit.
OBD code C0899 means Yaw Rate Sensor Circuit Range/Performance.
This code is triggered by the Electronic Brake Control Module (EBCM) when it detects an issue with the yaw rate sensor circuit.
The yaw rate sensor is part of the vehicle’s stability control system and measures the rate of rotation around the vehicle’s vertical axis.
When the sensor circuit’s performance is out of the specified range, the EBCM sets this diagnostic trouble code (DTC) C0899.
Mechanic’s Tech Notes
Code C0899 indicates a fault in the Electronic Brake Control Module (EBCM) motor relay circuit.
OBDII code C0899 indicates a problem with the Transmission Control Module (TCM) power circuit.
To diagnose, use a voltmeter to check TCM power and ground connections for proper voltage levels.
Utilize a scan tool to confirm TCM communication over the Controller Area Network (CAN) network.
Visually inspect wiring harnesses and connectors for any damage, and ensure connector pins are not broken, bent, pushed out, or corroded.
If all connections appear intact, consider reprogramming or reflashing the TCM as a potential fix.
FAQ
OBD code C0899 indicates a problem with the battery voltage, faulty control module, or related wiring issues. Check wiring harness, connectors, and components for damage.
Common symptoms for OBD code C0899 include Engine Light ON. Possible causes are battery voltage issues, faulty Control Module, or wiring harness problems. Inspect and repair as needed.
Diagnose OBD code C0899 by checking battery voltage, inspecting Control Module and harness for issues. Repair by examining wiring, connectors, and components for damage or corrosion.
Wrap Up
If your ABS warning light is illuminated and you retrieve OBDII code c0899, it may indicate a fault in the Electronic Brake Control Module (EBCM) or a communication issue within the system.
This could be caused by damaged wiring harnesses, poor connections, or a malfunctioning EBCM.
To address OBDII code c0899, start by inspecting the wiring harnesses and connectors for any visible damage.
Check for loose or corroded connections at the EBCM and wheel speed sensors.
If no issues are found, consider testing the EBCM for proper operation or replacing it if
