The OBD code P1017 for BMW indicates an issue with the Valvetronic Eccentric Shaft Sensor.
Symptoms include the Engine Light being ON.
This code is usually caused by a poorly installed reluctor on the sensor, a faulty sensor, open/shorted sensor harness, or poor electrical connection.
It is a moderate issue.
To fix, inspect the sensor, wiring harness, and connectors for any damage or poor connections.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
I know how frustrating it is to see that warning light pop up again and again. You don’t need to spend money at the mechanic just to clear it. With this pocket-friendly automatic car scanner, you can do it yourself in seconds and and avoid the time and inconvenience of driving to a mechanic. Just plug it in, connect to your Android or iOS phone, and instantly see live data. Understand the fault code, clear it right away, and decide if it’s something urgent or if you’re good to drive. It even monitors your car and sends notifications to your phone, so you’re always in control. Simple, fast, and stress-free—today’s offer price!
Symptoms of the Bmw p1017 OBD Code
The vehicle may experience rough idling and reduced engine performance with BMW fault code P1017.
- Symptoms: Engine Light ON.
- Rough idle may be experienced.
- Loss of power during acceleration.
- Engine may hesitate or stumble.
- Vehicle may exhibit poor fuel efficiency.
Causes of the Bmw p1017 OBD Code
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Fault code P1017 on BMW indicates an issue with the Valvetronic eccentric shaft sensor.
- P1017 can be caused by a poor installation of the reluctor on the Valvetronic Eccentric Shaft Sensor.
- A faulty Valvetronic Eccentric Shaft Sensor.
- An open or shorted harness on the Valvetronic Eccentric Shaft Sensor.
- A poor electrical connection in the Valvetronic Eccentric Shaft Sensor circuit.
Fixing Bmw Error Code p1017 Step By Step
Address the issue by inspecting and potentially replacing the Valvetronic eccentric shaft sensor.
- To fix BMW OBDII code P1017, review the possible causes mentioned above and visually examine the corresponding wiring harness and connectors.
- Ensure to check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.
- Check the operation of the intake camshaft sensor and replace it if necessary.
- Clear the fault codes from the vehicle’s computer using a diagnostic scan tool.
- Test drive the vehicle to verify that the code does not return.
- If the code persists, further diagnosis may be required to pinpoint the exact cause of the issue.
Cost Of Fixing Bmw p1017 Fault Code
Diagnosing and repairing BMW fault code P1017 may involve inspecting and replacing the VANOS solenoid.
The cost to diagnose and fix the BMW OBD code P1017 depends on the estimated 1. 0hour repair time.
Labor rates usually range from $75 to $150 per hour, so the total cost could be between $75 and $150. Factors like shop rates and the complexity of the repair can influence the final cost.
Details of the Bmw p1017 OBD Code
Code P1017 in BMW indicates an issue with the Valvetronic eccentric shaft sensor.
BMW OBD code P1017 means Valvetronic Eccentric Shaft Sensor Reference Voltage.
This code is triggered when the Engine Control Module (ECM) detects a voltage signal outside of the specified range from the Valvetronic eccentric shaft sensor.
The Valvetronic system is involved in controlling variable valve lift, improving engine efficiency and performance.
The eccentric shaft sensor provides feedback to the ECM regarding the position of the Valvetronic eccentric shaft, helping to optimize valve lift and timing.
Mechanic’s Tech Notes
Detailed information on BMW fault code P1017, including possible causes and diagnostic procedures.
To diagnose and fix OBDII code BMW P1017, start by visually inspecting the wiring harness and connectors related to the transmission control module (TCM).
Look for any damaged components and check connector pins for signs of damage or corrosion.
Use a multimeter to check TCM power and ground connections.
Additionally, use a scan tool to verify if the TCM is communicating over the Controller Area Network (CAN) network.
If necessary, consider reprogramming or reflashing the TCM.
This comprehensive approach will help identify and address potential issues causing the P1017 fault code.
FAQ
Common symptoms of BMW OBD code P1017 include Engine Light ON, caused by issues like poor sensor installation, faulty sensor, wiring harness problems. Fix involves thorough inspection and repair.
OBD code P1017 in BMW is typically caused by poor installation of the Valvetronic Eccentric Shaft Sensor reluctor, faulty sensor, or wiring issues. Inspect and repair as needed.
Diagnose and repair OBD code P1017 in BMW: Symptoms Engine Light ON. Causes Poor sensor installation, faulty sensor, wiring issues. Fix Inspect wiring, connectors, sensor installation.
Wrap Up
If your BMW is displaying OBD code P1017, you may experience rough idling, poor acceleration, or stalling.
This code typically indicates an issue with the Valvetronic eccentric shaft sensor, wiring problems, or a faulty Valvetronic motor.
To address BMW OBD code P1017, start by inspecting the wiring harness for any visible damage or loose connections.
Test the Valvetronic eccentric shaft sensor and motor for proper operation.
Replace any faulty components and ensure all connectors are securely attached to resolve the issue effectively.
