The OBD code B2132 indicates an issue with the Memory Recall Switch circuit.
This affects the Memory Mirror Module (MMM).
Symptoms include the Engine Light being ON.
The cause could be a faulty Memory Recall Switch or related wiring issues.
It’s not a severe issue but should be addressed.
A possible fix is to inspect the wiring harness and connectors for any damage or poor connections.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Symptoms of the b2132 OBD Code
The vehicle displays an airbag warning light on the dashboard with fault code B2132 stored.
- Symptoms: Engine Light ON.
- Possible loss of communication with the immobilizer control module.
- Difficulty starting the vehicle.
Do you know you can clear most fault codes—but some could mean serious danger? Don’t take chances with your safety or your family’s safety. This budget-friendly car scanner makes it easy to clear fault codes in seconds while showing you exactly what’s wrong. Plug it in, connect to your Android or iOS phone, and instantly check live data. You’ll know if it’s a minor issue you can clear or something serious that needs attention—so you can drive safely and stress-free. (Today’s Deal)
Causes of the b2132 OBD Code
B2132 fault code may be triggered by a faulty airbag module or wiring issue.
- B2132 can be caused by a faulty Memory Recall Switch.
- A Memory Recall Switch harness that is open or shorted.
- A Memory Recall Switch circuit with a poor electrical connection.
- A faulty Memory Mirror Module (MMM).
Fixing Error Code b2132 Step By Step
To address fault code B2132, inspect and repair the airbag driverside inflator circuit.
- To fix OBDII code B2132, first, review the possible causes related to this code.
- Visually inspect the wiring harness and connectors associated with the affected circuit.
- Check for any damaged components and ensure the connector pins are not broken, bent, pushed out, or corroded.
- If no issues are found during the visual inspection, proceed to test the affected component or sensor for proper operation.
- Replace the faulty component if necessary.
- Clear the fault codes using a scan tool and perform a road test to verify that the issue has been resolved.
Cost Of Fixing b2132 Fault Code
The repair for fault code B2132 may involve replacing the airbag deployment indicator.
The cost to diagnose and fix OBD code B2132 depends on the estimated 1. 0hour repair time.
Labor rates usually range from $75 to $150 per hour, so the total cost could be between $75 and $150. Factors like shop rates and complexity can influence the final cost.
That fault code is a turning point. If repair costs are climbing and your current loan feels like it’s holding you back, this is the time to plan ahead. The free Car Loan Payment Tracker helps you see how quickly you can pay off what’s left—and start preparing, with confidence, for your dream car.
Details of the b2132 OBD Code
B2132 code indicates a fault in the airbag deployment circuit.
OBD code B2132 means Front Wiper Motor Relay Circuit Short to Ground.
This code is triggered by the Body Control Module (BCM) when it detects a short to ground in the front wiper motor relay circuit.
The BCM monitors the voltage levels in the circuit, and if it detects a voltage that is lower than expected (indicating a short to ground), it will set this diagnostic trouble code (DTC) B2132. This code is specific to issues related to the front wiper motor relay circuit in the vehicle’s electrical system.
Mechanic’s Tech Notes
Code B2132 indicates a fault in the airbag driver side circuit.
To diagnose and fix OBDII code B2132, start by checking the Transmission Control Module (TCM) power and ground using a multimeter.
Verify TCM communication over the Controller Area Network (CAN) using a scan tool.
If the TCM does not respond, reprogramming or reflashing may be necessary.
Visually inspect the wiring harness and connectors for any damage, and check connector pins for signs of being broken, bent, pushed out, or corroded.
This code typically indicates a communication issue between modules, so ensuring proper power, ground, and communication signals are crucial for a successful repair.
FAQ
OBD code B2132 indicates an issue with the Memory Recall Switch circuit. Check for faulty switch, wiring, or Memory Mirror Module. Inspect and repair wiring connections as needed.
Common symptoms of OBD code B2132 include Engine Light ON, caused by a faulty Memory Recall Switch, harness issues, or a faulty Memory Mirror Module (MMM).
Diagnose OBD code B2132 by checking Memory Recall Switch and MMM. Inspect wiring for faults. Repair any damaged components or connectors.
Wrap Up
If your vehicle displays OBD code b2132, you may experience issues with the airbag system, such as an illuminated airbag warning light or nondeployment in a collision.
This code typically indicates a fault in the airbag deployment loop, which could be caused by a faulty airbag module, clock spring, or wiring harness connection.
To address OBD code b2132, start by inspecting the wiring harness and connectors for any signs of damage or corrosion.
Test the airbag module and clock spring for proper functionality, and ensure all connections are secure.
Replace any faulty components as needed
