[SOLVED] U182E Code: How To Fix Drive Motor Communication Loss

If you see the Engine Light ON or Service Engine Soon Warning Light in your car, it could be due to the automobile fault code: u182e. This code indicates a problem with the HybridEV Powertrain Control Module 2 or the Body Control Module (BCM). The possible causes include a faulty module, open or shorted harness, or poor electrical connection.

To fix the issue, you need to visually inspect the wiring harness and connectors for any damage or corrosion. The repair time for this fault code is 1.0, and it’s important to address the issue promptly to avoid further damage to your car.

Repair Importance Level	10.0 (Out of 10)
Estimated Repair Time	Approximately 1.0 hour
Repair Difficulty Level	10.0 (Out of 10)

Unveiling U182E: Common Symptoms You Shouldn’t Ignore

If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to the u182e fault code.

Here are the symptoms to look out for:

The automobile fault code U182E has the following symptoms: Engine Light ON (or Service Engine Soon Warning Light).

Decoding U182E: Common Causes Of The Fault Code

The automobile fault code u182e can be caused by a range of issues, including a faulty powertrain control module, poor electrical connections, and a faulty body control module.

The automobile fault code U182E can be caused by a faulty Hybrid/EV Powertrain Control Module 2.
It can also be caused by an open or shorted Hybrid/EV Powertrain Control Module 2 harness.
Another possible cause is a poor electrical connection in the Hybrid/EV Powertrain Control Module 2 circuit.
Lastly, a faulty Body Control Module (BCM) can also trigger this fault code.

Fix U182E: Simple Steps To Solve The Issue

Below are the possible fixes for the automobile fault code u182e, including inspecting wiring harness and connectors for damage or corrosion.

To fix the automobile fault code u182e, first, check the possible causes listed above.
Then, visually inspect the related wiring harness and connectors.
Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
This fix will take an estimated repair time of 1.0 hour.

Crunching The Numbers: U182E Repair Cost & Complexity

The automobile fault code U182E has an estimated repair time of 1.0 hour.

The cost of fixing this code varies depending on the auto repair shop, but it is common for them to charge between $75 and $150 per hour. These factors are influential in determining the overall cost of fixing the U182E fault code.

U182E: Your Car’s Oxygen Sensor Needs Attention

The U182E code is related to the serial data circuit in a vehicle.

It indicates that the Drive Motor Control Module 1 has lost communication with HybridEV Powertrain Control Module 2. This loss of communication can occur due to a power or ground failure.

The absence of a state of health message from the non-communicating device triggers the DTC. It is important to note that the DTC does not necessarily indicate a failure of the devices containing the stored code.

FAQ

What are the possible causes of the u182e automobile fault code?

If you see the engine light on or the service engine soon warning light, it could be due to the u182e fault code. This code is caused by a faulty Hybrid/EV Powertrain Control Module 2, an open or shorted Hybrid/EV Powertrain Control Module 2 harness, a poor electrical connection in the Hybrid/EV Powertrain Control Module 2 circuit, or a faulty Body Control Module (BCM). To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

How can I visually inspect the related wiring harness and connectors to fix the u182e fault code?

If you’re experiencing an Engine Light ON or Service Engine Soon Warning Light due to the u182e fault code, you can fix it by visually inspecting the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. Also, check for a faulty Hybrid/EV Powertrain Control Module 2, an open or shorted Hybrid/EV Powertrain Control Module 2 harness, a Hybrid/EV Powertrain Control Module 2 circuit poor electrical connection, or a faulty Body Control Module (BCM).

Is a faulty Body Control Module (BCM) a common cause of the u182e fault code?

The u182e fault code can be caused by a faulty Body Control Module (BCM), among other things. This can result in the engine light turning on or the service engine soon warning light. To fix the issue, it is recommended to check the possible causes listed, visually inspect the wiring harness and connectors, and look for any damaged components or corroded connector pins.

Wrap Up

If your engine light is on, it could be due to a faulty HybridEV Powertrain Control Module 2 or a poor electrical connection. Check the wiring harness and connectors for damage or corrosion. Look for broken, bent, or pushed out pins.

Inspect the BCM as well.