The automobile fault code U147D indicates a problem with the Right Blind Spot Sensor (RBSS) in your vehicle. The most common symptom is the Engine Light ON or Service Engine Soon Warning Light. The cause of this issue could be a faulty RBSS, an open or shorted harness, or a poor electrical connection.
It is important to address this issue promptly as it can affect the safety features of your vehicle. The repair time for this fault code is estimated to be around 1.0 hour. To fix the problem, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
Unveiling U147D: Common Symptoms You Shouldn’t Ignore
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the u147d fault code. Here are the symptoms to look out for:
- The U147D fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include issues with the transmission, such as difficulty shifting gears or the transmission slipping.
- The vehicle may also experience a decrease in power or acceleration, and the engine may stall or hesitate during operation.
- Additionally, the vehicle may experience issues with the brakes, such as reduced braking power or a spongy brake pedal.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
Decoding U147D: Common Causes Of The Fault Code
The automobile fault code u147d can be caused by a faulty sensor, open or shorted harness, or poor electrical connection.
- The automobile fault code U147D can be caused by a faulty Right Blind Spot Sensor (RBSS).
- It can also be caused by an open or shorted Right Blind Spot Sensor harness.
- Additionally, a poor electrical connection in the Right Blind Spot Sensor circuit can also trigger this fault code.
Fix U147D: Simple Steps To Get Your Car Running Again
Here are some possible fixes for the automobile fault code u147d:
- To fix the automobile fault code u147d, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
Crunching The Numbers: U147D Repair Cost & Complexity
The automobile fault code U147D can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops.
Therefore, the total cost of fixing the U147D fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.
U147D: Your Car’s Sos Signal For Steering Angle Sensor Failure
The Blind Spot Monitor (BSM) system has two components: Left Blind Spot Sensor (LBSS) and Right Blind Spot Sensor (RBSS).
The sensors are concealed behind the outboard ends of the rear bumper fascia. The microprocessor analyzes the sensor data to determine whether any detected objects should be reported.
When an object is detected, the Sensor controls its respective left or right BSM display directly through a hard-wired output to the Outside Rearview Mirrors. The sensor also sends an electronic request message over the CAN Bus to the radio.
The Radio then mutes any current output through the speakers and generates a chime as an audible alert. The Diagnostic Trouble Code (DTC) will set if incorrect data received from the Right Blind Spot Sensor (RBSS). The U147D Code indicates Implausible Data Received From Right Blind Spot S.
Each sensor performs a bulb test by illuminating the triangle icon in the Outside Rearview Mirror at each ignition ON cycle.
FAQ
If your engine light is on and you’re seeing the u147d fault code, it could be due to a faulty Right Blind Spot Sensor (RBSS), an open or shorted RBSS harness, or a poor electrical connection in the RBSS circuit. To fix the issue, start by visually inspecting the wiring harness and connectors for any damage or corrosion. Check for broken, bent, or pushed out connector pins and replace any damaged components as needed.
If you’re experiencing an illuminated Engine Light or Service Engine Soon Warning Light, it could be due to a faulty Right Blind Spot Sensor (RBSS), an open or shorted RBSS harness, or a poor electrical connection in the RBSS circuit. To fix this, visually inspect the wiring harness and connectors for any damage or corrosion. Check for broken, bent, pushed out, or corroded connector pins.
If you’re experiencing the u147d automobile fault code, you may notice that your engine light is on or that the service engine soon warning light is illuminated. This issue is typically caused by a faulty Right Blind Spot Sensor (RBSS), an open or shorted RBSS harness, or a poor electrical connection in the RBSS circuit. To troubleshoot this issue, you should visually inspect the related wiring harness and connectors, checking for damaged components and broken, bent, pushed out, or corroded connector pins. Be sure to check the “Possible Causes” listed above for additional guidance.
Wrap Up
If your engine light is on, it could be due to a faulty Right Blind Spot Sensor (RBSS), an open or shorted harness, or poor electrical connection. To fix it, visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
