[SOLVED] U0152 Code: Left Side Restraints Control Lost – Fix Now!

The automobile fault code U0152 indicates a problem with the Side Restraints Control Module Left in your vehicle. The most common symptom is the Engine Light turning on.

The cause of this issue could be a faulty module, an open or shorted harness, or a poor electrical connection. It is important to address this issue promptly as it can affect the safety of your vehicle. The repair process involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins.

The repair time for this issue is estimated to be around 1.0 hour. To interpret the fault code, it is recommended to check the “Possible Causes” listed above and visually inspect the related components.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the u0152 fault code. Here are the symptoms to look out for:

  • The U0152 fault code in an automobile can cause the following symptoms: – Engine Light ON (or Service Engine Soon Warning Light) – Loss of communication with the fuel pump control module – Issues with the fuel system – Problems with the transmission – Difficulty starting the engine – Reduced fuel efficiency – Rough idling or stalling – Reduced engine power – Issues with the vehicle’s performance – Failure of the vehicle to shift gears properly.

The u0152 automobile fault code can be caused by a faulty module, open or shorted harness, or poor electrical connection.

  • The automobile fault code U0152 can be caused by a faulty Side Restraints Control Module Left.
  • It can also be caused by an open or shorted harness in the Side Restraints Control Module Left.
  • Additionally, a poor electrical connection in the Side Restraints Control Module Left circuit can also trigger this fault code.

Below are some possible fixes for the automobile fault code u0152, including inspecting wiring harness and connectors for damage or corrosion.

  • To fix the automobile fault code u0152, first, check the possible causes listed above.
  • Then, visually inspect the related wiring harness and connectors.
  • Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The automobile fault code U0152 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour.

Therefore, the total cost of diagnosis and fixing the U0152 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to fix the issue.

The U0152 code is a Controller Area Network (CAN) fault code.

CAN is a vehicle bus standard designed to interconnect automotive devices without a host computer. The U0152 code sets when a periodic message from the Side Restraints Control Module Left has not been received.

CAN bus uses two dedicated wires for communication, CAN high and CAN low.

The Diagnostic Trouble Code (DTC) sets when there is a lost communication with the Side Restraints Control Module Left.

What are the possible causes of the u0152 automobile fault code?

If you see the engine light on or the service engine soon warning light, it could be due to the u0152 fault code. This code is caused by a faulty Side Restraints Control Module Left, an open or shorted harness, or a poor electrical connection in the circuit. To fix this issue, you should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

How can I fix the u0152 automobile fault code?

If you’re experiencing the u0152 fault code, you may notice that your engine light is on. This could be due to a faulty Side Restraints Control Module Left, an open or shorted harness, or a poor electrical connection in the circuit. To fix the issue, start by visually inspecting the wiring harness and connectors. Check for any damaged components and look for broken, bent, pushed out, or corroded connector pins.

What should I visually inspect to troubleshoot the u0152 automobile fault code?

If you’re experiencing the u0152 automobile fault code, you may notice that your engine light is on or that your service engine soon warning light is illuminated. The cause of this issue could be a faulty Side Restraints Control Module Left, an open or shorted Side Restraints Control Module Left harness, or a poor electrical connection in the Side Restraints Control Module Left circuit. To troubleshoot this issue, you should visually inspect the related wiring harness and connectors, checking for damaged components and looking for broken, bent, pushed out, or corroded connector’s pins.

u0152 error fault code explained

If your engine light is on, it could be due to a faulty Side Restraints Control Module Left, an open or shorted harness, or poor electrical connection.

Check the possible causes, inspect the wiring harness and connectors, and look for damaged components or corroded pins.

Scroll to Top