The P3414 fault code in automobiles indicates a problem with the Cylinder Deactivation Solenoid. The symptom is the Engine Light ON or Service Engine Soon Warning Light. The cause could be low oil pressure, restricted oil passage, engine mechanical condition, faulty Cylinder Deactivation Solenoid, Cylinder Deactivation Solenoid harness is open or shorted, or Cylinder Deactivation Solenoid circuit poor electrical connection.
The repair importance is high as it affects the engine’s performance.
The repair difficulty is moderate, and the fix involves visually inspecting the related wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins. The repair time is estimated to be 1.0 hour. To interpret the fault code, one needs to check the possible causes listed above.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P3414: Identifying Symptoms Of A Faulty Camshaft Position Sensor
If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p3414 fault code.
Here are the symptoms to look out for:
- The P3414 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include a decrease in engine power, rough idling, stalling, and poor acceleration.
- Additionally, the vehicle may experience misfires, reduced fuel efficiency, and difficulty starting.
- It is important to address these symptoms promptly to prevent further damage to the vehicle and ensure safe driving conditions.
P3414: Uncovering The Culprits Behind The Fault Code
P3414 fault code in automobiles can be caused by various factors, including low oil pressure, restricted oil passage, and faulty cylinder deactivation solenoid.
- The automobile fault code P3414 can be caused by low oil pressure, restricted oil passage, engine mechanical condition, faulty Cylinder Deactivation Solenoid, Cylinder Deactivation Solenoid harness being open or shorted, and Cylinder Deactivation Solenoid circuit having poor electrical connection.
Fix Code P3414: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code p3414, including inspecting wiring harness and connectors for damage or corrosion.
- To fix the automobile fault code p3414, you need to check the possible causes listed above.
- Visually inspect the related wiring harness and connectors for any damage.
- Look for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P3414: Affordable Fix For Complex Auto Fault Code
The automobile fault code P3414 can be diagnosed and fixed within an estimated repair time of 1.0 hour. The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour.
Therefore, the total cost of diagnosis and fixing the P3414 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to fix the issue.
P3414: The Low Voltage Saga Of Your Car’s Engine
The P3414 code refers to the cylinder deactivation system in the engine. The system deactivates certain cylinders to improve fuel economy.
The ECM commands the deactivation of cylinders 1 and 7 on the left bank, and cylinders 4 and 6 on the right bank. The deactivation is achieved by not allowing the intake and exhaust valves to open on the selected cylinders. The deactivation lifters contain spring-loaded locking pins that connect the internal pin housing of the lifter to the outer housing.
The locking pins are pushed inward with engine oil pressure directed from the valve lifter oil manifold (VLOM) assembly solenoids.
The switching between V8 and V4 mode is accomplished in less than 250 milliseconds.
FAQ
If you see the P3414 fault code on your vehicle, it means that the engine light is on. The possible causes of this fault code include low oil pressure, restricted oil passage, engine mechanical condition, faulty cylinder deactivation solenoid, cylinder deactivation solenoid harness is open or shorted, and cylinder deactivation solenoid circuit poor electrical connection. To fix this issue, you should check the possible causes listed above, visually inspect the related wiring harness and connectors, and look for damaged components and broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P3414 fault code, start by checking the possible causes listed above. To visually inspect the related wiring harness and connectors, look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues with the Cylinder Deactivation Solenoid harness and circuit connections.
The P3414 fault code is indicated by the Engine Light ON or Service Engine Soon Warning Light. The possible causes include low oil pressure, restricted oil passage, faulty Cylinder Deactivation Solenoid, and poor electrical connection in the Cylinder Deactivation Solenoid circuit. To fix the issue, one must visually inspect the wiring harness and connectors for any damage or corrosion and check for broken or bent pins.
Wrap Up
If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to low oil pressure, restricted oil passage, or a faulty Cylinder Deactivation Solenoid.
Check the possible causes listed above, visually inspect the wiring harness and connectors, and look for damaged components or corroded pins.
