[SOLVED] P2819 Code: Fixing Electrical Pressure Control Solenoid ‘h’

The P2819 automobile fault code indicates a problem with the Pressure Control Solenoid ‘H’ in the transmission system.

The most common symptom is the illumination of the Engine Light or Service Engine Soon Warning Light. The cause of this fault code could be a faulty solenoid, an open or shorted harness, poor electrical connection, or blockage in the transmission valve body.

The repair importance is high as it affects the transmission system’s performance. The repair difficulty is moderate, and the repair time is estimated at 1.0 hour. To fix the issue, one should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p2819 fault code.

Here are the symptoms to look out for:

  • The P2819 fault code in an automobile can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
  • Other symptoms may include issues with the transmission, such as difficulty shifting gears or the transmission slipping.
  • The vehicle may also experience reduced power or acceleration, and there may be a noticeable decrease in fuel efficiency.
  • Additionally, the vehicle may experience stalling or hesitation during acceleration, and there may be a rough or erratic idle.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle.

The automobile fault code P2819 can be caused by a faulty pressure control solenoid, open or shorted harness, poor electrical connection, or blockage in the transmission valve body.

  • The automobile fault code P2819 can be caused by a faulty Pressure Control Solenoid ‘H’.
  • It can also be caused by an open or shorted Pressure Control Solenoid ‘H’ harness.
  • Poor electrical connection in the Pressure Control Solenoid ‘H’ circuit can also trigger this fault code.
  • Additionally, a blockage in the Transmission Valve Body can also be a cause of the P2819 fault code.

Below are the possible fixes for the automobile fault code p2819, including inspecting wiring harness and connectors for damage or corrosion.

  • To fix the automobile fault code P2819, first, check the possible causes listed above.
  • Then, visually inspect the related wiring harness and connectors.
  • Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The automobile fault code P2819 can be diagnosed and fixed within an estimated repair time of 1.0 hour.

The cost of repair is influenced by the repair time, which is commonly charged between $75 and $150 per hour by most auto repair shops. Therefore, the total cost of diagnosis and fixing the P2819 fault code will depend on the hourly rate charged by the repair shop and the estimated repair time required to fix the issue.

The P2819 fault code is related to the Pressure Control Solenoid ‘H’ Electrical issue in the transmission system of the vehicle. The Transmission Control Module (TCM) uses the vehicle speed signal to determine the actual gear position.

The TCM compares the actual gear with the shift schedule in the TCM memory to detect shift solenoid valves and valve body mechanical problems.

The P2819 code indicates that there is an electrical problem with the pressure control solenoid ‘H’. This issue can cause problems with the shifting of gears and can lead to further damage to the transmission system if not addressed promptly.

It is important to have the vehicle diagnosed and repaired by a qualified mechanic to avoid further damage and costly repairs.

What are the possible causes of the P2819 automobile fault code?

If you see the engine light on or the service engine soon warning light, it could be due to the P2819 fault code. This code is caused by a faulty pressure control solenoid ‘H’, an open or shorted harness, poor electrical connection in the circuit, or a blockage in the transmission valve body. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.

How can I visually inspect the related wiring harness and connectors to fix the P2819 fault code?

If you’re experiencing the P2819 fault code, which is indicated by the engine light or service engine soon warning light turning on, there are a few things you can do to fix it. The cause of this issue could be a faulty pressure control solenoid ‘H’, an open or shorted harness, poor electrical connection, or a blockage in the transmission valve body. To address this problem, you should visually inspect the related wiring harness and connectors. Look for any damaged components and check for broken, bent, pushed out, or corroded connector pins.

What are the consequences of ignoring the P2819 fault code?

Ignoring the P2819 fault code, which indicates a faulty Pressure Control Solenoid ‘H’ or related issues, can lead to serious consequences. The engine light or service engine soon warning light will remain on, indicating a problem with the transmission valve body. It is important to check the possible causes listed above, visually inspect the wiring harness and connectors, and look for damaged components to avoid further damage.

p2819 error fault code explained

If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Pressure Control Solenoid ‘H’, an open or shorted harness, poor electrical connection, or blockage in Transmission Valve Body. Check the possible causes, inspect the wiring harness and connectors, and look for damaged components or corroded pins.

Scroll to Top