[SOLVED] P279B Code: Fixing Four Wheel Drive Low Range Performance

The P279B automobile fault code is a common issue that triggers the Engine Light ON or Service Engine Soon Warning Light. The cause of this fault code could be a faulty Engine Control Module, a poor electrical connection in the Engine Control Module circuit, or internal mechanical problems in the transmission. The importance of repairing this issue lies in the fact that it affects the performance of the vehicle and could lead to further damage.

The repair difficulty is moderate, and the repair time is estimated at 1.0 hour. To fix this issue, one should visually inspect the related wiring harness and connectors and check for damaged components. It is essential to interpret the fault code correctly to identify the root cause of the problem.

Repair Importance Level10.0 (Out of 10)
Estimated Repair TimeApproximately 1.0 hour
Repair Difficulty Level10.0 (Out of 10)

If you notice the Engine Light ON or Service Engine Soon Warning Light, it could be a sign of p279b fault code. Here are the symptoms to look out for:

  • The P279B fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
  • Other symptoms may include a decrease in fuel efficiency, difficulty shifting gears, and transmission slipping or jerking.
  • Additionally, the vehicle may experience a loss of power or acceleration, and the transmission may fail to engage or disengage properly.
  • It is important to address these symptoms promptly to prevent further damage to the vehicle.

The automobile fault code P279B can be caused by a range of issues, including reprogramming the ECM and faulty engine control modules.

  • The automobile fault code P279B can be caused by several factors.
  • These include the need to reprogram the Engine Control Module (ECM), a faulty Engine Control Module, an open or shorted Engine Control Module harness, poor electrical connection in the Engine Control Module circuit, and internal mechanical problems in the transmission.
  • All of these factors can contribute to the occurrence of the P279B fault code in automobiles.

To fix the automobile fault code p279b, check the possible causes and inspect the related wiring harness and connectors for any damage or corrosion.

  • To fix the automobile fault code P279B, you need to check the possible causes listed above.
  • Visually inspect the related wiring harness and connectors for any damage.
  • Look for broken, bent, pushed out, or corroded connector’s pins.
  • This fix will take an estimated repair time of 1.0 hour.

The automobile fault code P279B has an estimated repair time of 1.0 hour.

The cost of fixing this fault code is influenced by the repair time. Most auto repair shops charge between $75 and $150 per hour for their services. Therefore, the fixing cost of P279B will be between $75 and $150, depending on the repair time required.

The P279B fault code is related to the transfer case in an automobile. The Engine Control Module (ECM) uses two ways to determine if the transfer case is in 4WD Low, 4WD High, or Neutral.

The first way is to compare the transmission output speed sensor to the transfer case output speed sensor. The second way is to use a LAN message sent by the transfer case shift control module to the ECM.

If the first and second ways do not match while in 4WD Low, 4WD High or Neutral, then the Diagnostic Trouble Code (DTC) is set. The P279B code indicates a fault in the Four Wheel Drive Low Range Performance. No external circuit diagnosis is involved as the internal fault detection is handled inside the control module.

What are the possible causes of the P279B automobile fault code?

The P279B fault code in automobiles can be caused by a faulty Engine Control Module, open or shorted Engine Control Module harness, poor electrical connection in the Engine Control Module circuit, or transmission internal mechanical problems. The engine light or service engine soon warning light may turn on as a symptom. The fix involves visually inspecting the wiring harness and connectors, checking for damaged components, and looking for broken, bent, pushed out, or corroded connector’s pins.

How can one fix the P279B automobile fault code?

If you’re experiencing an illuminated Engine Light or Service Engine Soon Warning Light, it could be due to the P279B fault code. The issue may be caused by a faulty Engine Control Module, poor electrical connection, or internal mechanical problems with the transmission. To fix it, visually inspect the wiring harness and connectors for any damage or corrosion. Check for broken, bent, pushed out, or corroded connector pins. Additionally, reprogramming the Engine Control Module may be necessary.

What should be visually inspected when trying to fix the P279B automobile fault code?

If you’re trying to fix the P279B automobile fault code, start by visually inspecting the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins. Also, check the “Possible Causes” listed above, which include a faulty Engine Control Module, open or shorted Engine Control Module harness, poor electrical connection in the Engine Control Module circuit, or internal mechanical problems in the transmission.

p279b error fault code explained

If you see the Engine Light ON or Service Engine Soon Warning Light, it could be due to a faulty Engine Control Module, open or shorted harness, poor electrical connection, or transmission problems. Check the possible causes, inspect wiring harness and connectors, and look for damaged components or corroded pins.

Scroll to Top