The P2796 fault code in automobiles refers to a faulty Electronic Transmission Fluid Auxiliary Pump. The most common symptom of this issue is the Engine Light turning on or the Service Engine Soon Warning Light. The cause of this problem could be a faulty pump, an open or shorted harness, or a poor electrical connection.
It is important to fix this issue as it can lead to transmission failure. The repair time for this issue is around 1.0 hour. To fix this problem, one should visually inspect the wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
| Repair Importance Level | 10.0 (Out of 10) |
| Estimated Repair Time | Approximately 1.0 hour |
| Repair Difficulty Level | 10.0 (Out of 10) |
P2796: Identifying Transmission Slippage Symptoms
If you notice the Engine Light ON (or Service Engine Soon Warning Light), it could be due to the p2796 fault code. Here are the symptoms to look out for:
- The P2796 fault code in automobiles can cause several symptoms, including the engine light turning on or the service engine soon warning light appearing.
- Other symptoms may include issues with shifting gears, transmission slippage, decreased fuel efficiency, and difficulty accelerating.
- Additionally, the vehicle may experience harsh shifting or fail to shift into certain gears.
- It is important to address these symptoms promptly to prevent further damage to the vehicle.
P2796: Uncovering The Culprits Behind The Fault Code
The automobile fault code P2796 can be caused by a faulty pump, open or shorted harness, or poor electrical connection.
- The automobile fault code P2796 can be caused by a faulty electronic transmission fluid auxiliary pump.
- It can also be caused by an open or shorted electronic transmission fluid auxiliary pump harness.
- Additionally, a poor electrical connection in the electronic transmission fluid auxiliary pump circuit can also trigger this fault code.
Fix Code P2796: Simple Steps To Get Your Car Running
Below are the possible fixes for the automobile fault code: p2796, including inspecting wiring harness, connectors, and damaged components.
- To fix the automobile fault code P2796, first, check the possible causes listed above.
- Then, visually inspect the related wiring harness and connectors.
- Look for any damaged components and check for broken, bent, pushed out, or corroded connector’s pins.
- This fix will take an estimated repair time of 1.0 hour.
P2796: Affordable Fix For Complex Auto Issue
The automobile fault code P2796 can be diagnosed and fixed within an estimated repair time of 1.0 hour.
The cost of repair is influenced by the hourly rate charged by the auto repair shop, which typically ranges between $75 and $150 per hour.
Therefore, the total cost of diagnosis and fixing the P2796 fault code will depend on the hourly rate charged by the auto repair shop and the estimated repair time required to fix the issue.
P2796: Transmission Input Shaft Speed Sensor Circuit Range/Performance
The P2796 code is related to the Electronic Transmission Fluid Auxiliary Pump Control Circuit. This pump is responsible for keeping the transmission engaged when the engine is stopped and the transmission is in drive.
The Transmission Control Module (TCM) monitors the Electronic Transmission Fluid Auxiliary Pump Control Circuit and sets the OBDII code when the signal is out of factory specifications.
If you encounter this fault code, it is recommended to have a professional mechanic diagnose and repair the issue to avoid further damage to your vehicle.
FAQ
If you see the engine light on or the service engine soon warning light, it could be due to the P2796 fault code. This code is caused by a faulty electronic transmission fluid auxiliary pump, an open or shorted electronic transmission fluid auxiliary pump harness, or a poor electrical connection in the electronic transmission fluid auxiliary pump circuit. To fix this issue, you should visually inspect the related wiring harness and connectors, check for damaged components, and look for broken, bent, pushed out, or corroded connector’s pins.
If you’re experiencing the P2796 fault code, start by checking the “Possible Causes” listed above. To visually inspect the related wiring harness and connectors, look for damaged components and check for broken, bent, pushed out, or corroded connector’s pins. This will help you identify any issues with the Electronic Transmission Fluid Auxiliary Pump harness that may be causing the fault code.
If you’re fixing the P2796 fault code, look out for the Engine Light ON or Service Engine Soon Warning Light. The possible causes include a faulty Electronic Transmission Fluid Auxiliary Pump, an open or shorted Electronic Transmission Fluid Auxiliary Pump harness, or a poor electrical connection in the Electronic Transmission Fluid Auxiliary Pump circuit. To fix it, visually inspect the related wiring harness and connectors, and check for damaged components or broken, bent, pushed out, or corroded connector’s pins.
Wrap Up
If your engine light is on, it could be due to a faulty electronic transmission fluid auxiliary pump, an open or shorted harness, or poor electrical connection. Visually inspect the wiring harness and connectors for damage or corrosion.
Check for broken, bent, or pushed out connector pins.
